T-CON Check Spreadsheet

[perelandra]

Re: T-CON Check Spreadsheet

here's the data for the 3 boards I've tried:

t-con #1

AVDD 16V
VCOM 6.5V (labeled VCOM2 ?)
VGH 27V
VGL -8V
VGMA1 15.4V
VGMA2 15.4V
VGMA3 13.3V
VGMA4 12V
VGMA5 11V
VGMA6 10.5V
VGMA7 10V
VGMA8 10V
VGMA9 9.75V
VGMA10 12.9V
VGMA11 7V
VGMA12 15V
VGMA13 14.9V
VGMA14 13.9V
VGMA15 14.9V
VGMA16 13.5V
VGMA17 14V
VGMA18 13.9V
VGMA19 12.9V
VGMA20 12.5V
VGMA21 12V
VGMA22 11.5V

t-con #2

AVDD 16V
VCOM 2.8V (labeled VCOM2 ?)
VGH 26V
VGL -7V
VGMA1 15V
VGMA2 16V
VGMA3 12.9V
VGMA4 11.5V
VGMA5 10.9V
VGMA6 10V
VGMA7 9.8V
VGMA8 9.7V
VGMA9 9.2V
VGMA10 7.5V
VGMA11 7V
VGMA12 6.9V
VGMA13 6.3V
VGMA14 5.9V
VGMA15 4V
VGMA16 4V
VGMA17 3.1V
VGMA18 3.3V
VGMA19 3V
VGMA20 2V
VGMA21 0.01V
VGMA22 0.01V

t-con #3

AVDD 16V
VCOM 6.3V (labeled VCOM2 ?)
VGH 27V
VGL -7V
VGMA1 2V
VGMA2 7V
VGMA3 7V
VGMA4 7V
VGMA5 7V
VGMA6 7V
VGMA7 7V
VGMA8 7V
VGMA9 7V
VGMA10 7V
VGMA11 7V
VGMA12 6.8V
VGMA13 6.8V
VGMA14 13V
VGMA15 12.3V
VGMA16 10.3V
VGMA17 10.5V
VGMA18 11.3V
VGMA19 12V
VGMA20 13V
VGMA21 16V
VGMA22 16V

[perelandra]

Re: T-CON Check Spreadsheet

budm, I seem to be the only one active in this thread, but not sure you meant your reply for me? There is no heat transfer pad on the AS15 on this board.

[budm]

Re: T-CON Check Spreadsheet

I am surprised that it did not have one on the AS15.
Does the IC too hot to touch by fingers?

[perelandra]

Re: T-CON Check Spreadsheet

Hi budm, thanks for the help. I'll post an image of the board. This one (#3) does get screaming hot, and right away. Too hot to hold your finger on it. The last one I tested (#2) did not, so I didn't think to check this one until you asked.

[perelandra]

Re: T-CON Check Spreadsheet

It's an AS15-F, if that matters?

[michael dranfield]

Re: T-CON Check Spreadsheet

There is a very simple way to test this chip, leave the set on for 10 mins and if the chips faulty it will be hot to touch, it should run stone cold .

[perelandra]

Re: T-CON Check Spreadsheet

Thanks Michael, it was burning hot within seconds.

[budm]

Re: T-CON Check Spreadsheet

I just replaced the burnt out AS15 on the T-CON board on 46" SAMSUNG, power it up without the ribbon cables between the LCD panel and the T-CON, no heat no smoke, unplug the power and connect all the ribbon cables, applied the power and turned on the TV, in less than a minute the IC smoked!

[keeney123]

Re: T-CON Check Spreadsheet

v1.1
Bug fix:
- handle symmetry curve check >18 items (typo)
- new symmetry display
- formatting improvements
- added "v1.1" to title

Tom66 nice piece of work. I'm sure those who repair TV's on a regular bases will find this invaluable.

[perelandra]

Re: T-CON Check Spreadsheet

Tom66, your spreadsheet tool is great! Very helpful!

I'm sorry for tagging onto your thread, but I thought that's what I was supposed to do. Although I've been lurking on badcaps for over 5 years I wasn't allowed to start a new thread. Guess I jumped through the right hoops, now little status deal says I can. Still don't have edit/delete privileges so I can't remove.

Guessing that starting a new thread now with my issues would be wrong, so I hope the mods will see this and advise?

[Agent24]

Re: T-CON Check Spreadsheet

I just replaced the burnt out AS15 on the T-CON board on 46" SAMSUNG, power it up without the ribbon cables between the LCD panel and the T-CON, no heat no smoke, unplug the power and connect all the ribbon cables, applied the power and turned on the TV, in less than a minute the IC smoked!

Could a bad panel cause that?

[budm]

Re: T-CON Check Spreadsheet

Yes, it is the bad panel that takes out the AS15.
I took the T-CON board out and replace the IC again but install the T-CON on anther SAMSUNG same model and panel without any problem, so now I have spare power supply, T-CON, and Main board for the next repair works.

[perelandra]

Re: T-CON Check Spreadsheet

Yes, it is the bad panel that takes out the AS15.
I took the T-CON board out and replace the IC again but install the T-CON on anther SAMSUNG same model and panel without any problem, so now I have spare power supply, T-CON, and Main board for the next repair works.

So, am I correct in assuming that if I do not connect up the ribbon cables (from t-con to panel) I will not damage a t-con board, if I indeed have a bad panel?

Last "used" (supposedly tested by seller) t-con board I tired I did exactly this (no panel connections) and AS15 was screaming hot from the get-go (immediately after power on), and bad voltage readings too. Just want to make sure nothing coming through the LVDC could be taking out the t-con boards.

[grumpy_one]

Re: T-CON Check Spreadsheet

I hope I'm not interrupting this thread, but I want to thank tom66 for all that he has revealed about AS15 ICs. It has been extremely helpful to me. I was just given a Samsung LA40B650 with a solarized picture (both picture and menu affected). Shopjimmy's videos assured me that I needed to look at the T-Con, and with tom66's posts I went straight to the AS15-U. It got warm after a couple of minutes running, though I could hold my finger on it without pain. So I checked the VGMA test points:
VG1 15.54
VG2 15.19
VG4 12.88
VG6 10.99
VG8 10.26
VG10 7.93
VG11 7.80
VG12 7.08
VG13 6.87
VG15 5.87
VG17 11.92
VG19 2.93
VG21 0.70
VG22 0.41

Based on tom66's posts, I mentally connected the warm AS15-U, and the very odd voltage on VG17, and decided I needed a new AS15-U. Unfortunately fate conspired against me - I then bought a heat gun on ebay, and when it arrived found it was defective. Seller would not give a refund until I posted it back to China for evaluation, so while I was waiting I bought a new T-Con board and fitted it. Great picture, no solarization. So, please chalk up one more win for tom66's posts.

If I eventually get the ebay situation sorted out I'll get a heat gun that works and replace the AS15-U on the original T-Con board - but this forum has already made it easy to repair what was previously a throw-away TV. Thanks everyone.

[steves7839]

Re: T-CON Check Spreadsheet

v1.1
Bug fix:
- handle symmetry curve check >18 items (typo)
- new symmetry display
- formatting improvements
- added "v1.1" to title

Cells B21 and B22 on the "Detailed..." tab have duplicate cell references to the Input tab. Easy fix but the reference should be sequential.

Question? Is there a generic way to find these test points, particularly VGMAn?
I'm fixing a Sony T-Con board.

[Ronald49]

Re: T-CON Check Spreadsheet

Thank you for this usefull tool!

I am testing my v520h1-c06 TCON. It doesnt have a AVDD test point, but a VDD and VDA. Which one do i need to fill in the spreadsheet?

It's for the Samsung LE40N87BD, problem is image persistence.

[Schaefer]

Re: T-CON Check Spreadsheet

Thank you, this is very helpful

[Brian10m]

Re: T-CON Check Spreadsheet

Tried the updated software V1.1 in excel 2016 32-bit, all seems ok. well done, nice job.

[Wilderone]

Re: T-CON Check Spreadsheet

Nice work, Thanks for sharing Tom66

[nobbnobb1]

Re: T-CON Check Spreadsheet

Thanks for this spreadsheet! I am diagnosing a blank screen issue on a Sony KLV-46W400A and these are my test values:

VCOM_D 10.9
VCOMG2L 6.4
VCOMG1 6.2

VON 20.8
VOFF -7.5

VMGA1 15.1
VMGA2 15.1
VMGA3 15.1
VMGA4 15.1
VMGA5 15.1
VMGA6 15.1
VMGA7 15.1
VMGA8 15.1
VMGA9 15.1
VMGA10 0
VMGA11 0
VMGA12 0
VMGA13 0
VMGA14 0
VMGA15 0
VMGA16 0
VMGA17 0
VMGA18 0

It's weird that VGMA #1-9 puts out the correct voltage but VMGA #10 - 18 puts out 0 volts. I'm guessing this is a definitive result that my T-Con board is bad?