-
-
Re: Eeprom dump thread!
Well, the dump size has become smaller, don't pay attention to it, write it down as it is.Comment
-
Polaroid TV switch off after logo display
Hello,
I am looking for the Dump Firmware of this model.
Mark: Polaroid
Model: TQL48R4PR003
Main board chassis: CV9203H-A42
LCD Screen / Panel: 15y_s48ff11mb7s4lv0.1
More information: W25Q32
thank you for your replyComment
-
Re: Eeprom dump thread!
plase dump Samsung LT22D390EW main BN41-02152B.zipComment
-
Re: Eeprom dump thread!
[QUOTE=lotas;1136795]Samsung LT22D390EW/EN Dump[
thanks frindComment
-
Samsung UN40H5103AFXZP
Hi
I am trying to find the eeprom dump for this tv, thanks.Comment
-
Re: Eeprom dump thread!
Model: Saba LD32VS249
MainBoard: 17MB97Comment
-
Re: Eeprom dump thread!
i need dump
PANASONIC TX-47ASW804 TNPH1111
thanks in advanceComment
-
Re: Eeprom dump thread!
Guys need help.. need dump for konka model KDE24PH313L
thanks..Never stop LEARNING because life never stops TEACHING!Comment
-
Re: Eeprom dump thread!
konka model KDE24PH313L
24 inch LCD TV TP.MS3663.PA671Attached FilesNever stop LEARNING because life never stops TEACHING!Comment
-
-
Re: Eeprom dump thread!
tv turns on and off after 3 seconds after displaying konka logo all voltages are present.. 1.2v 3.3v 5v and 12v.Never stop LEARNING because life never stops TEACHING!Comment
-
Last edited by Duranitron; 06-05-2022, 08:09 PM.Never stop LEARNING because life never stops TEACHING!Comment
-
Last edited by Duranitron; 06-06-2022, 05:12 AM.Never stop LEARNING because life never stops TEACHING!Comment
-
Re: Eeprom dump thread!
Sorry, this is a complicated procedure, you can’t explain it in a nutshell.Comment
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.07-26-2025, 03:24 PM -
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I...
Comment