Re: Eeprom dump thread!
second attempt
re read this time selecting:
24 eeprom
AMTEL
AT24C128
from menu on left
sorry im new to this
second attempt
re read this time selecting:
24 eeprom
AMTEL
AT24C128
from menu on left
sorry im new to this
-
-
Re: Eeprom dump thread!
Try it, there are two dumps from different models, but the main is the same for everyone.Comment
-
Re: Eeprom dump thread!
thanks for your effort ,
sadly fault still same
but at least i know that i now have the correct eeprom data
would it be worth buying a new blank eeprom and writing the bin file to it?Comment
-
Re: Eeprom dump thread!
just a quick question
IN ch431a s/w programmer :
with eeprom M24128 BRMN6TP
do i select AT24C128B
or :AM24C128 ?
i selected:AM24C128 and wrote to eeprom
was that correct?Comment
-
Re: Eeprom dump thread!
In eeprom there is no difference which letter is at the end, the main size is "128".Comment
-
Re: Eeprom dump thread!
ok thank youComment
-
Re: Eeprom dump thread!
Pleas I want dump for OLYMPIC model EVA32LED4B main tp.ms3393.p85 think for helpComment
-
Re: Eeprom dump thread!
only the red led. without turning on.Comment
-
Re: Eeprom dump thread!
Dump corruptComment
-
Re: Eeprom dump thread!
LOTAS: it worked perfect. I thank you from my heart. A hugComment
-
Re: Eeprom dump thread!
Do you have a YouTube user to follow you or a social network?Comment
-
Re: Eeprom dump thread!
hi can help me plase dump
LISTO 18.5LEDHD-477
MAIN-CV309L-A
U11-W25Q32V
PANEL-M185XW01Comment
-
dump LISTO 18.5LEDHD-477
hi can help me plase dump
MAIN-CV309L-A
U11-W25Q32V
PANEL-M185XW01Comment
-
Re: Eeprom dump thread!
thanksComment
-
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... -
Comment