phillips lcd keeps blowing fuse

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • TimT
    Badcaps Veteran
    • Nov 2012
    • 268
    • us

    #81
    Re: phillips lcd keeps blowing fuse

    the tv does not turn off. I can barely see the menu. ajusted brightness up..no change.

    Comment

    • MisterD
      Badcaps Veteran
      • Oct 2012
      • 668
      • United States

      #82
      Re: phillips lcd keeps blowing fuse

      I assume you have the back off the TV and can't you see the backlight lit up? usually seen through the holes or slots in the metal chassis.

      Comment

      • TimT
        Badcaps Veteran
        • Nov 2012
        • 268
        • us

        #83
        Re: phillips lcd keeps blowing fuse

        No backlight! The " phillips " is on screen for about 3 seconds. but for the first half second its bright. i can still see it and the menu using a flash light at a angle... that's how hard it is to see it!

        Comment

        • MisterD
          Badcaps Veteran
          • Oct 2012
          • 668
          • United States

          #84
          Re: phillips lcd keeps blowing fuse

          I just fixed a 47" Philips that was doing something similar, It would not shut off, the remote control did nothing, the backlights would come on for an instant then right back off, my problem was the Mainboard was not sending the signal to the Power Supply, replacing the Main Board also known as the Small Signal Board fixed my problem, there may be a way for you to make the backlights come on with an external 3v source, do you see a marking on the power supply board next to the white connector labeled BL_ON ?

          Comment

          • MisterD
            Badcaps Veteran
            • Oct 2012
            • 668
            • United States

            #85
            Re: phillips lcd keeps blowing fuse

            I found a picture of a power supply board that is used for your Model TV, on the white connector I see a pin labeled BL-3V, the best way I found is to take a safety pin and shove it into that part of the connector to make contact with the 3V connection, then you need to take a reading with your meter set to DC Volts, hook the black prob to the chassis for ground and then touch the red prob to the safety pin connection to the BL_3V Pin and see what voltage reading you get, it should be near 3 Volts.

            Comment

            • TimT
              Badcaps Veteran
              • Nov 2012
              • 268
              • us

              #86
              Re: phillips lcd keeps blowing fuse

              I wii test this tomorrow. thank you

              Comment

              • TimT
                Badcaps Veteran
                • Nov 2012
                • 268
                • us

                #87
                Re: phillips lcd keeps blowing fuse

                Here are the readings from the mainboard connector and inverter connector.

                main

                tuner 35v is getting 39v
                lcd 12
                lcd 12
                p+on 3.36v
                +6.5vf or 1v gets 11v
                p-on 3.5v or reg gets 6.70
                p+ on 5v
                24v for amp gets 27.8

                inverter

                power sel 0
                bl adj is not used
                bl 5w gets 3w
                error 0
                gnd
                gnd
                gnd
                gnd
                gnd
                24v
                24v
                24v
                24v
                24v

                not sure how to inturpet these results?
                there is a 10amp SMF on inverter and it's getting 9.6 on both ends. inverter lights up for a split second thats when i see the " phillips " when inverter goes out the phillips is still there. then I see the no signal. this is extremely hard to see! I can ajust the sound/channels ect it works fine. menu works fine. powers off and on correctly. seems everything works fine just no backlight.
                Attached Files

                Comment

                • MisterD
                  Badcaps Veteran
                  • Oct 2012
                  • 668
                  • United States

                  #88
                  Re: phillips lcd keeps blowing fuse

                  Originally posted by TimT
                  Here are the readings from the mainboard connector and inverter connector.

                  main

                  tuner 35v is getting 39v
                  lcd 12
                  lcd 12
                  p+on 3.36v
                  +6.5vf or 1v gets 11v
                  p-on 3.5v or reg gets 6.70
                  p+ on 5v
                  24v for amp gets 27.8

                  inverter

                  power sel 0
                  bl adj is not used
                  bl 5w gets 3w
                  error 0
                  gnd
                  gnd
                  gnd
                  gnd
                  gnd
                  24v
                  24v
                  24v
                  24v
                  24v

                  not sure how to inturpet these results?
                  there is a 10amp SMF on inverter and it's getting 9.6 on both ends. inverter lights up for a split second thats when i see the " phillips " when inverter goes out the phillips is still there. then I see the no signal. this is extremely hard to see! I can ajust the sound/channels ect it works fine. menu works fine. powers off and on correctly. seems everything works fine just no backlight.


                  Default Re: phillips lcd keeps blowing fuse
                  Here are the readings from the mainboard connector and inverter connector.

                  main

                  tuner 35v is getting 39v
                  lcd 12
                  lcd 12
                  p+on 3.36v
                  +6.5vf or 1v gets 11v
                  p-on 3.5v or reg gets 6.70
                  p+ on 5v
                  24v for amp gets 27.8

                  inverter

                  power sel 0
                  bl adj is not used
                  bl 5w gets 3w ? Is this possibly bl SW getting 3V ?
                  error 0
                  gnd
                  gnd
                  gnd
                  gnd
                  gnd
                  24v
                  24v
                  24v
                  24v
                  24v

                  Comment

                  • TimT
                    Badcaps Veteran
                    • Nov 2012
                    • 268
                    • us

                    #89
                    Re: phillips lcd keeps blowing fuse

                    Sorry, you are correct bl sw 3v

                    Comment

                    • MisterD
                      Badcaps Veteran
                      • Oct 2012
                      • 668
                      • United States

                      #90
                      Re: phillips lcd keeps blowing fuse

                      I think that bl sw could be the same as bl_on which is at 3v and it seems like that would cause the inverter to fire up the backlights..can you hook your volt meter to this pin again and monitor the voltage? see what the voltage is when you first power on the TV, then leave the meter probe in place and see if this voltage stays constant, report your readings back here.

                      Hopefully budm and tom66 can help with this one. See Post#77, he has replaced the Power Supply Board.
                      Last edited by MisterD; 12-29-2012, 09:06 PM.

                      Comment

                      • budm
                        Badcaps Legend
                        • Feb 2010
                        • 40746
                        • USA

                        #91
                        Re: phillips lcd keeps blowing fuse

                        OK, this TV uses:
                        PWM-SEL pin for lamp brightness control, it is being used by this TV.
                        BL-ADJ is the analog signal control for the lamp brightness, and it is not being used.
                        BL-SW is the same as BL_ON. You need to monitor this test point when the TV is plugged in but the power switch is not activated. Then hit the power switch and see if the voltage at this point changes state.
                        I believe you are getting the correct signal (3V as you had indicated).
                        I need to see good close up of the inverter board/s.
                        Never stop learning
                        Basic LCD TV and Monitor troubleshooting guides.
                        http://www.badcaps.net/forum/showthr...956#post305956

                        Voltage Regulator (LDO) testing:
                        http://www.badcaps.net/forum/showthr...999#post300999

                        Inverter testing using old CFL:
                        http://www.badcaps.net/forum/showthr...er+testing+cfl

                        Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                        http://s807.photobucket.com/user/budm/library/

                        TV Factory reset codes listing:
                        http://www.badcaps.net/forum/showthread.php?t=24809

                        Comment

                        • TimT
                          Badcaps Veteran
                          • Nov 2012
                          • 268
                          • us

                          #92
                          Re: phillips lcd keeps blowing fuse

                          When I plug this TV in it automatically starts up..no stand by. not shure if thats normal for this TV. I can turn it off with the power button I think that may put it in stand by?

                          when plugged in I hear the " click " from power board. bl SW is 0 then in about 3 seconds it jumps to 2.99 to 3.00v " this is when the backlight kicks in for a split second " it stays at 3v untill I turn the TV off with power button then bl SW is back to 0. I can turn it pack on with power button with the same results.

                          here are 3 pictures of inverter board. I will post another picture of the other board. and a picture of the way I tested this. Thanks for your help! on the picture labeled connect the connector 4p is getting 1.6v if i remember correctly.
                          Attached Files

                          Comment

                          • MisterD
                            Badcaps Veteran
                            • Oct 2012
                            • 668
                            • United States

                            #93
                            Re: phillips lcd keeps blowing fuse

                            I noticed in your pictures of the inverter board that some of the mounting screws are missing, all of the screws must be in place and tightened to ensure a good ground connection from the board to the chassis, this can cause this type of problem. you should make sure all circuit boards have all the mounting screws in place and are snugged down tight. Also it appears that there is something hanging off where the SMF (F1) is mounted to the board, has this fuse been replaced? make sure that is not something shorting to another connection on the board, I believe I saw a previous post about the voltage readings being the same on both sides of this fuse, maybe you should do a continuity check by measuring resistance on this fuse with the meter in both directions. set your meter to ohms on 200 scale. just 200 Not 200k or 200m, just 200 ohms.
                            Last edited by MisterD; 12-30-2012, 11:04 AM.

                            Comment

                            • TimT
                              Badcaps Veteran
                              • Nov 2012
                              • 268
                              • us

                              #94
                              Re: phillips lcd keeps blowing fuse

                              sorry, this does go into standby mode.. plugged in there is a " tick " but does not power up untill power button is pressed. more pictures
                              Attached Files

                              Comment

                              • budm
                                Badcaps Legend
                                • Feb 2010
                                • 40746
                                • USA

                                #95
                                Re: phillips lcd keeps blowing fuse

                                OK, the 3v is = Backlights on, and that signal is correct. So now we need to find out why the lamps turn off even though you do have the necessary voltage (24vdc) and the BL_ON signals.
                                The problem can be bad caps (black electrolytics caps), transformers, lamps, bad connection on the board fingers that make contact with lamps.
                                I would carefully remove the board and clean the contacts pads real well on the inverter board fingers, also look real close at all the sockets where the board fingers are plugged into, see if there is any sign of heat (plastic housing has brownish color).
                                Can I also see the whole pictures of the inverter board?
                                Never stop learning
                                Basic LCD TV and Monitor troubleshooting guides.
                                http://www.badcaps.net/forum/showthr...956#post305956

                                Voltage Regulator (LDO) testing:
                                http://www.badcaps.net/forum/showthr...999#post300999

                                Inverter testing using old CFL:
                                http://www.badcaps.net/forum/showthr...er+testing+cfl

                                Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                                http://s807.photobucket.com/user/budm/library/

                                TV Factory reset codes listing:
                                http://www.badcaps.net/forum/showthread.php?t=24809

                                Comment

                                • selldoor
                                  Slow Learner
                                  • Dec 2010
                                  • 7870

                                  #96
                                  Re: phillips lcd keeps blowing fuse

                                  I am off to bed he has posted pics of the inverter board but has had to split into 4 in post92

                                  There is one white fuse that I can see in pic 1 That should be tested.

                                  The inverters are HS482 TM10BS I cant see any but the tm series seem to have the secondaries along one side - see pic.
                                  Meter on ohms 2000 test S1>S2 and S3>S4 for each transformer and post results.
                                  There are quite a lot of Mosfets (Might be 50N04 s )on the board - Q designation and they should be tested also.
                                  Attached Files
                                  Last edited by selldoor; 12-30-2012, 04:47 PM.
                                  Please upload pictures using attachment function when ask for help on the repair
                                  http://www.badcaps.net/forum/showthread.php?t=39740

                                  Comment

                                  • budm
                                    Badcaps Legend
                                    • Feb 2010
                                    • 40746
                                    • USA

                                    #97
                                    Re: phillips lcd keeps blowing fuse

                                    I saw those pictures in post 92, but I can figure it out a little better if i get to see the whole board also, I can see on small current sensing transformer on the board.
                                    Never stop learning
                                    Basic LCD TV and Monitor troubleshooting guides.
                                    http://www.badcaps.net/forum/showthr...956#post305956

                                    Voltage Regulator (LDO) testing:
                                    http://www.badcaps.net/forum/showthr...999#post300999

                                    Inverter testing using old CFL:
                                    http://www.badcaps.net/forum/showthr...er+testing+cfl

                                    Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                                    http://s807.photobucket.com/user/budm/library/

                                    TV Factory reset codes listing:
                                    http://www.badcaps.net/forum/showthread.php?t=24809

                                    Comment

                                    • MisterD
                                      Badcaps Veteran
                                      • Oct 2012
                                      • 668
                                      • United States

                                      #98
                                      Re: phillips lcd keeps blowing fuse

                                      As I posted in Post # 93, The Inverter Board has some mounting screws missing as I can see in the picture, these circuit boards need all the screws in place and tightened down to make a ground connection, please answer my question, did you install all of these screws and tighten them down? did you make sure every circuit board has all the screws and that they are all tightened down? please reply back to let us know. Thanks.

                                      Comment

                                      • TimT
                                        Badcaps Veteran
                                        • Nov 2012
                                        • 268
                                        • us

                                        #99
                                        Re: phillips lcd keeps blowing fuse

                                        MisterD When testing all boards are bolted back down. selldoor the SMF near connector is a 10A fuse I tested it right at 10v. but ill need to recheck the rating. I cant remember the correct voltage but 10v is close.
                                        pulled and cleaned inverter but no luck. as far as i know nothing has been replace on this board. power board is " new " from Encompass parts. budm no brownish color at inverter contacts looked clean.
                                        Attached Files

                                        Comment

                                        • budm
                                          Badcaps Legend
                                          • Feb 2010
                                          • 40746
                                          • USA

                                          #100
                                          Re: phillips lcd keeps blowing fuse

                                          That white fuse is fed by the 24V power supply, and you are reading 10V, that does not sound right to me. You can see that the fuse is connected to those red wires for the 24v feeding.
                                          Never stop learning
                                          Basic LCD TV and Monitor troubleshooting guides.
                                          http://www.badcaps.net/forum/showthr...956#post305956

                                          Voltage Regulator (LDO) testing:
                                          http://www.badcaps.net/forum/showthr...999#post300999

                                          Inverter testing using old CFL:
                                          http://www.badcaps.net/forum/showthr...er+testing+cfl

                                          Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                                          http://s807.photobucket.com/user/budm/library/

                                          TV Factory reset codes listing:
                                          http://www.badcaps.net/forum/showthread.php?t=24809

                                          Comment

                                          Related Topics

                                          Collapse

                                          • Dannyx
                                            UC3842 Power Adapter Blowing Fuse
                                            by Dannyx
                                            Good day folks......wow this new layout is weird. It's like I woke up one day and I'm no longer on Planet Earth or something

                                            Anyway....got this here power brick from a USB to SATA adapter which keeps blowing the fuse after I almost repaired it. The reason I even bother to fix a power brick (wall wart, whatever) in the first place is because this thing was really convenient to use: I'd just plug it and that's it. It's a dual output supply, for both 12v and 5v, which although I COULD easily obtain with a DC-DC converter from a standard 12v adapter, I thought I should crack open the...
                                            12-05-2023, 12:06 PM
                                          • Tips
                                            Samsung PD27AOQ (BN44-00506B) constantly blowing internal fuse.
                                            by Tips
                                            Looking for some assistance please.
                                            Trying to repair a PD27AOQ samsung power board.
                                            Initially had the typical problem of cm806 capacitor blown, additionally thermistor NT801s blown.
                                            Replaced the ceramic capacitor, str60252s, bridge rectifier, thermistor and fuse.
                                            Testing it the fuse blows immediately power is turned on.
                                            diodes dm852 and dm853 test as shorted when in the board but fine when removed.
                                            any assistance, guidance would be appreciated.
                                            04-11-2024, 11:24 AM
                                          • RogerH58
                                            Samsung 46" TV LE46B530 blowing fuse
                                            by RogerH58
                                            Hi all,

                                            I am a newbie and not very experienced so bear with me if i struggle sometimes with technical language - but I'll do my best. I searched "Samsung" and the model number on the forum but didn't find anything I could understand!

                                            I'm not an electronics guy - just picked up stuff over the years through my flight-simming hobby.

                                            I have the above mentioned 46" tv as the monitor for my flight-sim setup. Recently it went "crack" and stopped working. No standdby light and no response. I assumed a fuse had blown and after investigation...
                                            06-10-2023, 10:27 AM
                                          • corrize
                                            A funny fuse story – Lumix LX100 II
                                            by corrize
                                            Hello, I disassembled this dead camera, and found this WTF… Two fuses soldered one above the other !
                                            I was pretty sure nobody touched it before, but that can't be from factory. There is flux, and capacitor is probably missing.
                                            The other weird thing : the fuses are « G » fuse : (0.75A – 8V), seems very low. The original fuse should be « O » : (32V 2,5A).
                                            There is « O » mark beside. All fuses have the same mark letter on main board. So, I can deduce it's a « O » fuse.
                                            And this correspond to the issus I saw : when I plug the battery, I measure the voltage dropping...
                                            10-19-2023, 09:58 AM
                                          • Bootleg1
                                            Samsung UN65KS9800FXZA T-con fuse blowing
                                            by Bootleg1
                                            Hi all, so i was watching tv acreen went black and no sound. Traced problem to blown tcon fuse. Replaced and it blows replaced again samething. So my tcon fuse keeps blowing. I bought a new board havent installed yet infear its just going to keep blowing the fuse. If i only connect the right side ribbon cable the fuse doesnt blow but as soon as i connect the left cable my tcon fuse instantly blows and no picture. The right side picture works clear as day and left side picture is grey (picture attatched) im hoping its a bad tcon board itself or a cable or anything and not the panel. Thank you for...
                                            02-04-2020, 01:05 AM
                                          • Loading...
                                          • No more items.
                                          Working...