Re: Eeprom dump thread!
Hello,
i need firmware for RCA 32
Board: TP.MS3393.PB855
Hello,
i need firmware for RCA 32
Board: TP.MS3393.PB855
-
-
Re: Eeprom dump thread!
TV starts normally when put in Smart mode TV shows this ...
TP.MS3393.PB855
I need the firmware if anyone has them please
⚠ This Firmware is damaged ⚠
Non-working firmware dump: https://www.mediafire.com/file/pm7ri...6S-SM.BIN/file
32 inches
modelo: RCA32A16S-SM
Board: TP.MS3393.PB855Last edited by Steve007iii; 08-06-2021, 03:41 PM.Comment
-
Re: Eeprom dump thread!
Your software is fine, I cut off the eeprom now try to write it down
if it fails, replace the SPI Flash with a new one.Comment
-
Re: Eeprom dump thread!
NAND GODDAMN!!!
it also has an android subsystem
Not everything is lost
someone in this forum was asking for this firmware for this board, there it is tested and working
32 inches
Model: RCA32A16S-SM
Board: TP.MS3393.PB855
https://www.mediafire.com/file/5r88m...nches.rar/fileLast edited by Steve007iii; 08-06-2021, 08:48 PM.Comment
-
Re: Eeprom dump thread!
The firmware on your TP.MS3393.PB855 is ok, you need to look for the usb firmware on the android module or somehow enter recovery and do a reset.Attached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: Eeprom dump thread!
i hope some one can help
i need dump for Soniq L32V12A 32" LCD
thanksComment
-
Re: Eeprom dump thread!
Ciao
Tv lg47le5308
Main. Eax61766102(0)
Pannello lc470EUHComment
-
Zenon ZN-AHD-5016 software
Zenon ZN-AHD-5016 software is needed. 25L12835F used. Fault: The device is stuck in the text zenon. There are all voltages.
Mainboard: GM8210-AHD-16CH
Flash ıc: 25L12835FAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: Eeprom dump thread!
hi.
i need emmc dump
sony
kd-49xe8096
main
1-981-326-12
(173633712)
GN3TR
thank you
The TV turns on and shows only the SONY logo.
I found
KD-55XF7596
KD-43XF7596
nothing changes, after resetting it needs to be refreshed via usb, and again only the SONY logoComment
-
Re: Eeprom dump thread!
ٍٍSony BRAVIA® KDL-40EX500
System Software Update (version 1.514)
May Be Useful and HelpComment
-
Re: Eeprom dump thread!
Thank youComment
-
Re: Eeprom dump thread!
JVC LT-50C550
UK model 55" TV
Screen - V500HJI-PE8
PSU - TV5001-ZC02-01
Main - MSDV3255-ZC01-01
TCON/Panel - Innolux V500HJI-XRME1 / V500HJI-PE8
NAND - Toshiba TC58NVG1S3HTA00
From a working TV that had LED backlight strips replaced.
No password, 2 part rar.Comment
-
Re: Eeprom dump thread!
Hi! I need the dumps for a cheap Trevi TV.
Model DTV-2522CI
Main HK-7050-CI-V3.04-B
Panel M215HW01
Don't actually care if it's Trevi branded or not, I just care if it works for watching TV.
Thank you
DavideComment
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.07-26-2025, 03:24 PM -
Hi, all
I need the dump/firmware for this tv, it was on a boot loop, i dont have the original corrupted dump because i used a pen drive with a firmware that solved the boot loop, initially it seemed it was ok but the tv has no sound
Thanks10-17-2025, 03:51 AM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work....
Comment