Sony LED 65X9005A shuts down after few seconds - looking for help

[Diah]

so now you have 4 parts only fly out

[tec3000]

no its not worse,, the empty trace at COF ribbon cable are normal... only the parts you found keep them spectated as photos location to bring them back by soldering

Thank you Diah. OK I'm relieved. I thought they were traces of burning or something...

Now, what happens if I solder them and it doesn't solve my problem? I tried to google the buffer boards for my model but can't find anything! And I'm not sure if I really have all lost parts. They are super tiny...

[tec3000]

so now you have 4 parts only fly out

maybe more. I will need to inspect further. It's tiny and there is also a lot of dirt inbetween. I can't be sure right now.

[Diah]

don't hurry... i think lotas eyes better than my as he discovered... so let wait on lotas advice of the location then you can start soldering them back

[tec3000]

Ok thank you, I have also no experience in soldering and no device here. But I will do it of course if that solves the problem.

[Diah]

it will be good idea to post photo on each 4 caps you found to see them clearly

[lotas]

Everything I saw, the most important thing is not the capacitors, here you need to solder a zero resistor or put a jumper on the chip.

[lotas]

It's hard to see on this bar...

[tec3000]

Everything I saw, the most important thing is not the capacitors, here you need to solder a zero resistor or put a jumper on the chip.

Thank you lotas I appreciate you took time to inspect the bars and marked them.

So, just to check... You say "solder a zero resistor or put a jumper on the chip". Does that mean I DO NOT need to solder back the parts that fell off?? Instead I have to buy some resistors and solder them on each bar? And you say OR jumper? So is that an option I have? I have zero experience with these things...

I retook pics of the second board. I can also retake better pics of the other board if you like.

[Diah]

Everything I saw, the most important thing is not the capacitors, here you need to solder a zero resistor or put a jumper on the chip.

you mean R007.. i don't think its in use,.... OP you need to shoot very clear photo on the area close to the IC

[tec3000]

you mean R007.. i don't think its in use,.... OP you need to shoot very clear photo on the area close to the IC

OK, I think it's best to shoot during daylight. It's extremely hard to get good pics right now. I will do ASAP.

[Diah]

OK, I think it's best to shoot during daylight. It's extremely hard to get good pics right now. I will do ASAP.

don't use the mobile camera in flash light mode... just use external light like ( torch ) on the area

[tec3000]

don't use the mobile camera in flash light mode... just use external light like ( torch ) on the area

Ok, will do! Thank you for the suggestion.

[lotas]

you mean R007.. i don't think its in use,.... OP you need to shoot very clear photo on the area close to the IC

R007 is torn off and hanging on one side, if it is alive (has a short circuit), then just solder it on both sides.

[lotas]

Check R2, it should also show a short circuit (0 Ohm).

[lotas]

And then check RH4, it’s hard to see.

[Diah]

yours photo , here could be parts falling down too

[tec3000]

yours photo , here could be parts falling down too

Ah! I forgot to tell you about it. I was able to identify the mysterious "L" on the left bottom of the TV. Luckily I didn't even have to disassemble anything. One problem less!

[tec3000]

don't use the mobile camera in flash light mode... just use external light like ( torch ) on the area

I have retaken the pictures. I will upload them now.

[tec3000]

this is board 1: