found this abortion in an hp laptop/tablet.
a surefire way to finish off an already problematic nvidia chip!
a surefire way to finish off an already problematic nvidia chip!
Attached Files
-
-
Re: heatsink fail!
Quata strikes again.sigpic
(Insert witty quote here) -
Re: heatsink fail!
Ouch. Let me guess:
"Why is my computer so loud?"
Comment
-
Re: heatsink fail!
lol, someone trying to use a penny or some sort in this laptop. Doing it wrong, though!
I, however, would never have done this.Recovering a BEFSR41 v1 and v2 router from solid red DIAG Light
I have two v2s and one v1.
I am still looking at these boards nearly every day.
What I'm doing: Planning an upgrade of my mining setup from Block Erupters to Red Furys.
Though, if the Block Erupters don't sell, I will keep using them for a while.Comment
-
Re: heatsink fail!
Maybe that's why the HP Compaq Athlon II laptop I was working on back in April shut down once under a light load!
ASRock B550 PG Velocita
Ryzen 9 "Vermeer" 5900X
32 GB G.Skill RipJaws V F4-3200C16D-32GVR
Arc A770 16 GB
eVGA Supernova G3 750W
Western Digital Black SN850 1TB NVMe SSD
Alienware AW3423DWF OLED
"¡Me encanta "Me Encanta o Enlistarlo con Hilary Farr!" -Mí mismo
"There's nothing more unattractive than a chick smoking a cigarette" -Topcat
"Today's lesson in pissivity comes in the form of a ziplock baggie full of GPU extension brackets & hardware that for the last ~3 years have been on my bench, always in my way, getting moved around constantly....and yesterday I found myself in need of them....and the bastards are now nowhere to be found! Motherfracker!!" -Topcat
"did I see a chair fly? I think I did! Time for popcorn!" -ratdude747Comment
-
Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
I have peltir element glued to heatsink with something thick and sticky like putty... it cant be separate with force or heat without risk of breaking ceramic or damaged semiconductor layers due to force (eg if try twisted, pulled, lifted)... method that I am using is a single thread for needle (thin and firm thread of pure polyester that cant break with bare hands without glowes), and using it like a saw between heatsink and peltir. I holding a heatsink with knee against table. It slowly cut throug putty and release glued parts. It is slow proces, but preserve undamaged component and heatsink....
-
Hello everyone,
I'm looking to upgrade the heatsink on the main processor of my TV's motherboard for better cooling performance.
The current heatsink is a square-shaped one (2.8cm x 2.8cn) with a basic design, and I believe a more efficient heatsink could help with thermal management and potentially extend the life of the TV.
I'd appreciate any advice on the best type of heatsink to use, specific product recommendations, and tips for installation.
If you've done a similar upgrade, I'd love to hear about your experience and any challenges you... -
I have RX26PG2 graphic card with incomplete original heatsink, only aluminium plate... but in original solution it look like such bad termal design that I asking if is proper fanless heatsink be adequate replacement ot better... what you think? Till powering on, it is propper hot......
-
Well, due to my grid tie inverter not accepting high voltages, and the fact that the lions in my solar panels are 36V (72-cell) I think I need to stick with 72-cell.
However I have a few smaller panels that are 36, 32, and two 30-cell. The 36 and 32 together run at 75% efficiency (and subtract more with additional inefficiencies) when running in parallel with the 72-cell panels. The kicker is that the two 30s... generate 0% power when connected in parallel(!)
So now what to do with these small panels?
I could sell them...
Or I could shim them....
Comment