See pictures below
Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
Sony XR-77A80J OLED 5 Blink
Collapse
X
-
Originally posted by EazyBone View Post
Comment
-
Originally posted by Diah View Post
you are the owner of this threat and you know better than us all.... so do yours human job lol
Comment
-
Diah I apologize for my lack of knowledge and not paying attention as much as I should. My readings were incorrect as you stated as I did not read the pins on the bottom part of the connector. I have been stopping my work on other repairs to learn TV's and have noticed my mind has been split between this and working on my other repairs so I apologize for my absent mind during these posts!
In saying that I do have 3.5v for the STBY. Staying on 2 I still don't have any readings on the 2 black connectors going to the T-CON as well as the white connector.
EazyBone I also was laughing at myself going back through these posts lol. I also apologize for adding two pages to this thread of nonsense haha
Comment
-
Originally posted by ChattFix View PostDiah I apologize for my lack of knowledge and not paying attention as much as I should. My readings were incorrect as you stated as I did not read the pins on the bottom part of the connector. I have been stopping my work on other repairs to learn TV's and have noticed my mind has been split between this and working on my other repairs so I apologize for my absent mind during these posts!
In saying that I do have 3.5v for the STBY. Staying on 2 I still don't have any readings on the 2 black connectors going to the T-CON as well as the white connector.
EazyBone I also was laughing at myself going back through these posts lol. I also apologize for adding two pages to this thread of nonsense haha
jumper STBY to pin 5 ( Power ON, & to pin 3 EVDD ON, and to pin 1. t-con on see the photo i attached at my post 84
turn ON and look at the screen how it will come on with pattern color
Comment
-
Originally posted by Diah View Post
disconnect the MB socket from PSU , and disconnect the 2 LVDS from T-CON, the sockets between PSU and T-CON should be in place
jumper STBY to pin 5 ( Power ON, & to pin 3 EVDD ON, and to pin 1. t-con on see the photo i attached at my post 84
turn ON and look at the screen how it will come on with pattern color
Comment
-
Originally posted by ChattFix View Post
I have 3.5v going to pin 1,3,5 but no picture. Do I need to jump some points to turn the TV on or do I just plug it in?
Comment
-
Originally posted by Diah View Post
if you did the jumpers correctly on the assigned pins. and you plug the tv in wall.... if no screen... test the sockets on the t-con all at fuses from both side if you have V.
Comment
-
Originally posted by ChattFix View Post
I'm getting 12.8v from 3 pins on the white socket but nothing from the black sockets.
Comment
-
Originally posted by Diah View Post
you need now take out the PSU alone on table and do the jumpers all 3 as i wrote before and trouble shooting the circuit of EVDD circuit at cold area... u worked on it before... you may forget put back the R in place LOl or missed with some parts
Comment
-
Originally posted by ChattFix View Post
Put it on the table and the bridge is good. CN6601 only have 12.8v in Pin 1 and 3, Pin 2 only has .07. Everything else is 0v. What is the R or LOI?
Comment
-
Originally posted by ChattFix View Post
Resistor is getting 12.8v on the positive side. Bin 3 socket 6401 is getting 3.5v
Comment
Comment