Alienware M14x R2 with 7 beeps error
Collapse
X
-
Comment
-
-
Re: Alienware M14x R2 with 7 beeps error
yes 17v is normal for that point.
remove the battery from your laptop until you fix it.
now measure voltage on all pins of PU701 after turning on.
avoid shorting neighbor pins together.Last edited by caspian; 09-17-2017, 01:03 AM.Comment
-
Comment
-
-
Re: Alienware M14x R2 with 7 beeps error
PU701
1 - 0.6mV
2 - 0.6mV
3 - 0.6mV
4 - 0.1mV
5 - 0.844V
6 - 1.060V
7 - 0.978V
8 - 1.060V
9 - 3.290V
10 - 0.2mV
11 - 0.9mV
12 - 0.9mV
13 - 0.9mV
14 - 0.9mV
15 - 0.9mV
16 - 0.9mV
17 - 0.9mV
18 - 0.2mV
19 - 19.5mV when not beeping, 19.9mV when 7 beeps are sounding
20 - 2.256V when not beeping, flashes between 2.256V and around 2.201V when 7 beeps are sounding
21 - 0.9mV
22 - 0.9mV
23 - 0.1mV
24 - 1.350V when not beeping, flashes between 1.350V and around 1.310V when 7 beeps are sounding
25 - 2.575V when not beeping, flashes between 2.575V and around 2.490V when 7 beeps are sounding
26 - 2.576V when not beeping, flashes between 2.576V and around 2.490V when 7 beeps are sounding
27 - 0.9mV
28 - 0.9mV
29 - 0.9mV
30 - 2.264V when not beeping, flashes between 2.264V and around 2.220V when 7 beeps are sounding
31 - 2.267V when not beeping, flashes between 2.267V and around 2.213V when 7 beeps are sounding
32 - 0.5mV
33 - 0.5mV
34 - 0.1mV
35 - 1.344V when not beeping, flashes between 1.344V and around 2.220V when 7 beeps are sounding
36 - 0.5mV
37 - 0.1mV
38 - 0.5mV
39 - 0.5mV
40 - 0.5mVComment
-
Comment
Related Topics
Collapse
-
Hi all.i have problem with my alienware 15 r2.basically its keep beeping 4 times at startup-what means there is ram issue.i already tried 10 different ram sticks with different speeds and voltages but nothing helps.tried to flash bios to see if that will help-but no luck.
Ram sockets looks fine as well,cleaned them and carefully inspected
So maybe someone had this problem as well with any of dell laptops and have some ideas what else i can do?
Thanks05-23-2023, 12:48 PM -
by Sus256Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
by tech_guruHello.
I am having a disappointing motherboard repair with this laptop and I need your help.
This came in with water damage, doing absolutely nothing, and had almost all standby voltages shorted. I have already replaced all those shorted components:
-UE5 SIO KB9022QD - Programmed spare one, when replaced, 3.3v short got out
-PQ102 MDV1525URH
-U17 AOZ1331
-UE1 C8051F383-GQ
-PU800 SY8032ABC
-UI2 SY6288D20AAC
-PU508 RT6220AHGQUF 7P=
-PU100 TPS51225CRUKR
-PU300 TPS51212DSCR
Now, I get all the standby voltages, it turns... -
by zwectI have this Alienware 17 laptop with the VAS00 LA-9331P REV 1.0 motherboard that does not turn on anything when power is plugged in and gives the 7 beep sequence, CPU / GPU does not heat up, i tried only with an I5 4200M (the laptop did not come with either the GPU or the CPU, but on the back says that it originally came with the Nvidia 860M and an 4710MQ).
While i do not know if there is any CPU blacklisting system on the motherboard, i tried reflashing the BIOS (at UH14) and the EC (at U2) accordingly but no changes either.
PCH doesn't seem to be shorted but i haven't done... -
by Superbee_dadHello Sharp TV experts
Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.
> I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
> There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...01-24-2025, 11:51 PM - Loading...
- No more items.
Comment