P5PE-VM question ?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bianchi77
    Badcaps Legend
    • Jun 2016
    • 1121
    • Australia

    #1

    P5PE-VM question ?

    Guys,

    I got P5PE-VM....I put the CPU and memory in it,
    I can turn it on but nothing is happened, no beep at all and
    POST code on diagnostic = 00, I have replaced the CPU with another CPU which is working on another board, still the same issue...

    How do you reckon ?
  • bianchi77
    Badcaps Legend
    • Jun 2016
    • 1121
    • Australia

    #2
    Re: P5PE-VM question ?

    I have a strange voltage value on some FETs ...3.2V...any opinions ?

    Comment

    • bianchi77
      Badcaps Legend
      • Jun 2016
      • 1121
      • Australia

      #3
      Re: P5PE-VM question ?

      could it be a corrupted bios ? can I write *.rom straight away with flash programmer without utility...since I can't boot to DOS ?

      Comment

      • diif
        Badcaps Legend
        • Feb 2014
        • 6978
        • England

        #4
        Re: P5PE-VM question ?

        Is the cpu compatible with the motherboard ?

        Comment

        • bianchi77
          Badcaps Legend
          • Jun 2016
          • 1121
          • Australia

          #5
          Re: P5PE-VM question ?

          yes I'm using Celeron D which is working on another board ...

          Comment

          • bianchi77
            Badcaps Legend
            • Jun 2016
            • 1121
            • Australia

            #6
            Re: P5PE-VM question ?

            I got only 00 on POST diagnostic and fan spinning..

            Comment

            • bianchi77
              Badcaps Legend
              • Jun 2016
              • 1121
              • Australia

              #7
              Re: P5PE-VM question ?

              I'm thinking uploading :
              http://dlcdnet.asus.com/pub/ASUS/mb/...316.1472338911
              Straight to the BIOS chip...
              I have G540 flash programmer...

              Comment

              • bianchi77
                Badcaps Legend
                • Jun 2016
                • 1121
                • Australia

                #8
                Re: P5PE-VM question ?

                *.rom is equal to *.bin or *.hex ? or I must use a special software from asus ?
                AFUDOS.exe

                Because I can't even access FDD or CDROM

                Comment

                • diif
                  Badcaps Legend
                  • Feb 2014
                  • 6978
                  • England

                  #9
                  Re: P5PE-VM question ?

                  Try renaming the .ROM to .BIN

                  Comment

                  • bianchi77
                    Badcaps Legend
                    • Jun 2016
                    • 1121
                    • Australia

                    #10
                    Re: P5PE-VM question ?

                    the chip :
                    W39V040FCPZ

                    Comment

                    • bianchi77
                      Badcaps Legend
                      • Jun 2016
                      • 1121
                      • Australia

                      #11
                      Re: P5PE-VM question ?

                      Ready to burn but not sure if the file is right
                      Attached Files

                      Comment

                      • selldoor
                        Slow Learner
                        • Dec 2010
                        • 7870

                        #12
                        Re: P5PE-VM question ?

                        Have you checked the Cmos battery is ok.
                        Can I assume you have the attached?
                        Section2.1.2 suggests that the file should perhaps be renamed P5PEVM.ROM

                        Can you make a bootable floppy in another PC and add the rom to it then try it in the machine with the new board from a cold start. (maybe disconnect the hard drive and CD so it doesnt try to boot from them?

                        Was the board supposed to be working, when you got it?
                        Have you tried starting without any ram - any beeps then?
                        Attached Files
                        Please upload pictures using attachment function when ask for help on the repair
                        http://www.badcaps.net/forum/showthread.php?t=39740

                        Comment

                        • bianchi77
                          Badcaps Legend
                          • Jun 2016
                          • 1121
                          • Australia

                          #13
                          Re: P5PE-VM question ?

                          There was no beep, it was not working when it came, *.rom file = *.bin file ?
                          POST CODE = 00.....PLED is not on....

                          Comment

                          • bianchi77
                            Badcaps Legend
                            • Jun 2016
                            • 1121
                            • Australia

                            #14
                            Re: P5PE-VM question ?

                            Can I assume you have the attached?...Do you mean battery attached ?

                            Comment

                            • bianchi77
                              Badcaps Legend
                              • Jun 2016
                              • 1121
                              • Australia

                              #15
                              Re: P5PE-VM question ?

                              Drain to Source = 0 ohm on 3 FETs ...9T15GH, 5503 x2

                              Comment

                              • bianchi77
                                Badcaps Legend
                                • Jun 2016
                                • 1121
                                • Australia

                                #16
                                Re: P5PE-VM question ?

                                Does anyone know the buck controller for P5PE-VM ??

                                Comment

                                • momaka
                                  master hoarder
                                  • May 2008
                                  • 12168
                                  • Bulgaria

                                  #17
                                  Re: P5PE-VM question ?

                                  Originally posted by bianchi77
                                  Drain to Source = 0 ohm on 3 FETs ...9T15GH, 5503 x2
                                  I guess you don't really care to fully try to read my posts about this issue in your other threads, but I will try again here...

                                  It is OKAY *most of the time* if MOSFETs show 0-10 Ohms resistance between Drain <-> Source leads if they are near the CPU. The CPU VRM has "lower" and "upper" MOSFETs. The lower MOSFETs have their Sources tied to ground and Drain tied to the inductors that output the V_core rail to the CPU. Because most CPUs (and GPUs too, FYI) have a low static resistance, the V_core rail will also show the same low resistance to ground. This means that the lower MOSFETs mentioned above will *appear* to have a short-circuit (0 to 10 Ohms) between Source and Drain as well.

                                  If those MOSFETs were truly shorted, you motherboard would not *stay* turned ON. At most, you will get a brief fan spin and then the motherboard would turn OFF - that's a tell-tale sign of something being shorted.

                                  Comment

                                  • bianchi77
                                    Badcaps Legend
                                    • Jun 2016
                                    • 1121
                                    • Australia

                                    #18
                                    Re: P5PE-VM question ?

                                    If those MOSFETs were truly shorted, you motherboard would not *stay* turned ON. At most, you will get a brief fan spin and then the motherboard would turn OFF - that's a tell-tale sign of something being shorted.

                                    I got that case on Asus A7S333, what's shorted in this case ? one of CPU VRM FET, or the the whole lot, there are 4 FETs near the CPU, if I release the CPU, fan keep spinning.....

                                    Comment

                                    • bianchi77
                                      Badcaps Legend
                                      • Jun 2016
                                      • 1121
                                      • Australia

                                      #19
                                      Re: P5PE-VM question ?

                                      Here are some photos....I can see CLK LED on POST diagnostic very dim....does it mean that this board has a CLK problem ?
                                      Attached Files

                                      Comment

                                      • bianchi77
                                        Badcaps Legend
                                        • Jun 2016
                                        • 1121
                                        • Australia

                                        #20
                                        Re: P5PE-VM question ?

                                        The video when I turned it on :
                                        https://youtu.be/_AS9uQU6XS8

                                        Comment

                                        Related Topics

                                        Collapse

                                        • Document Archive
                                          Postcard 32 4-Bit 4-Digit Diagnostic Card PC Analyzer Manual
                                          by Document Archive
                                          Postcard 32 4-Bit 4-Digit Diagnostic Card PC Analyzer Manual

                                          Diagnostic Card is a powerful diagnostic tool for technicians and administrators to troubleshoot
                                          various problems of IBM compatible PCs. It is easy to install, yet extremely powerful to use. With
                                          Diagnostic Card in hand, you no longer have to go through tedious and time consuming process of
                                          trying to figure out what is wrong with your PC hardware. Diagnostic Card will tell you exactly
                                          what is wrong with your PC in just seconds. It saves you time and money.

                                          Our new and improved design...
                                          11-01-2024, 06:29 AM
                                        • MisterAIL
                                          PS5 digital / No Power / No Beep / Good power supply
                                          by MisterAIL
                                          Hi everyone,

                                          Brought a non functionnal PS5. Apparently only a bad PSU...
                                          No beep, nothing.

                                          After some tests i found this :
                                          - PSU is fine (12 volts stable)
                                          - 12 volts line is shorted
                                          - DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
                                          - By the way, nothing change. No signal, no power, no beep.

                                          Mesuring all rails with my workbench psu (12 volts input)
                                          - 0.00 amp drawing
                                          - 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is...
                                          03-12-2024, 03:24 PM
                                        • ktmmotocross
                                          Ps5 pro - one beep and not start after hdmi port change and decoder ic reflow
                                          by ktmmotocross
                                          Hello.
                                          Have this ps5 pro EDM033 that came with damaged hdmi connector. i replace it and console works for few days but show hdmi problems when cold start. so cold joint. reflowed connector and decoder ic as i think he have cold joint. but now i have only one beep and no start. can heatdamage of this decoder ic prevent start?

                                          i have ps5 repair guide but not ps5 pro so link me to it if u know it
                                          04-27-2025, 01:10 AM
                                        • teokarafou
                                          Lenovo Ideapad 5 15ARE05-2 beep
                                          by teokarafou
                                          Hello team ,I a have ideapad 5 ,that has a weird issue ,it start up and does 2 beep ,and when I want to type password to login,keyboard doesn’t work ,check video


                                          Lenovo ideapad 5 15are05
                                          s/n: pf2hngt3...
                                          12-27-2024, 08:40 AM
                                        • Ymotaqi
                                          ROG STRIX Z590-A GAMING WIFI has no POST no BEEP no diag LED
                                          by Ymotaqi
                                          The motherboard does not POST and has the following symptoms:
                                          When the power button is pressed, the fans and RGB turns on.
                                          When the power button is pressed, the motherboard voltages 12, 5, and 3 are connected.
                                          The motherboard does not beep.
                                          None of the diagnostic LEDs light up.
                                          USB voltage is off.
                                          VCORE voltage is off.
                                          The BIOS software was downloaded from Asus site and installed using the Q FLASH button, but it made no difference.
                                          I would appreciate it if anyone could guide me on the cause of the problem.
                                          ​
                                          01-12-2025, 04:15 AM
                                        • Loading...
                                        • No more items.
                                        Working...