ktmmotocross
Boardkiller
Last Activity: Yesterday, 07:02 AM
Joined: 02-16-2014
Location: slovakia
-
pray u dont have ripped pads under core...Leave a comment:
-
Leave a comment:
-
shorted memory chip and shorted memory DRMOSLeave a comment:
-
so u need to find strap resistors. page 11...Leave a comment:
-
u can edit bios so windows wont update it...Last edited by ktmmotocross; 11-29-2024, 11:15 PM.Leave a comment:
-
why dont u check guide videos on youtube. there is some procedure what to check as a beginnerLeave a comment:
-
u can only compare to other boards. check if u have pgood on 1.8V ic and follow it...Leave a comment:
-
bad delid on 12900K, have anyone measuring of components on top of cpu?
have this badly delided intel 12900K wth knock off components, have anyone measurements of components on top of cpu? -
come on guys it is just register . this app will be needed further for repairsLeave a comment:
-
i tried but stencill will bend by heat. only good for small chips.
i cut stopbumps on classic 90x90 holder and now it takes all chipsLeave a comment:
-
RX7xxx MPS monitor app - only for corporate mails - can somebody register - download and share
On RX7xxx is use controllers from MPS. on their page it is app to monitor this controllers. but accout must be registered from corporate mail. Can anybody register, download and share this app
[url]https://www.monolithicpower.com/en/computing-and-telecom-core-gui.html#social-login-popup[/url]https://On RX7xxx is use controllers...ml#social-logi -
PS5 after PSU burn wont start
Hello.
HAve this PS5 that have burned control ic in PSU. After replace i get only one beep when start button press. I found 1.3 ohm on HDMI encoder so i remove it and short gone.
On my PSU show 0.006A and when start button is presed it goes to 0.027A and goes back down. Looks like i have all standby voltages except 1.8V from dialog ic. no short on that rail. i try to inject it but still the same.
is worth try to replace this dialog ic ?... -
board after start show 00 post code - where to search for fault
Hello.
Have some boards that shows 00 post codes when started. flashed bios, check voltages. I suspicious chipset dont comunicate. Any hint? -
old Intel 180GB SSD not work controller ic getting hot can be data recovered after replace it?
Hello.
Have this old ssd from intel that not work . owner have data to save. can be ssd repaired and data recovered just by replacing controller ic? -
come on guys nobody?Leave a comment:
-
no body?...Leave a comment:
-
Asus Zephyrus G15 GA503QS not start when ram is in slot. works only on onboard ram
Hello.
Have this Asus Zephyrus G15 GA503QS that not start when ram is in slot. works only on onboard ram. i try multiple 3200Mt rams but still the same. i try poking pins of connector but it looks ok. on ram i found 2.5V and 1.2V. Dont have any idea whats wrong.
Any hint? -
Hello.
Have this Lenovo T480 NM-B501 that is not charging. USB-C stays on 5V, Mechanic USB-C tester shows that both ports are ok.
Read about u15 bios corruptions. i try to make and flash new bios but it did not help, maybe because it needs HEX editing which i sucks in.
maybe somebody allready doing this can help.
s/n - PF-15vjjb 18/08...Leave a comment:
-
found one mosfet with G-S short. after replace it workLeave a comment:
No activity results to display
Leave a comment: