-
Full-time computer repair tech (10am - 6pm) and full-time, (8am - 11pm), Ruby on Rails Developer
-
Re: Polaroid P40LED13 powers up then shuts down
I've recently repaired one of these with no backlight but it was not a led problem.
I'm sure ReeceyBurger123 had a video highlighting two capacitor to check for possible failure which led me to finding C525 faulty.
Here are the notes I made.
No led backlights.
PFC circuit not running. No VCC for U101 PFC controller (FAN7529). C525 low resistance / capacitance. Replaced the 1uF 50V. VCC now up to 10.5V. Min voltage needs to be 14.5V for PCF to run. Further checks found Q216 (BC327) with collector/base short circuit. Replaced BC327 and set now up and running.Willing to help but I'm no expert.Comment
-
Re: Polaroid P40LED13 powers up then shuts down
I'll check that out when I get to work but in my case, when the tv turns on, the backlight comes on for a split second then goes out and no image on tv; tv is NONE operational. Removing the led wire the tv IS operational, just no backlight. So something is making the tv NONE operational when the led wire is attached to the psu.Full-time computer repair tech (10am - 6pm) and full-time, (8am - 11pm), Ruby on Rails DeveloperComment
-
Re: Polaroid P40LED13 powers up then shuts down
Sounds to me like a bad connection in the Led strings causing intermitent backlight.Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: Polaroid P40LED13 powers up then shuts down
The fault is different to mine in as much as the set did power up but just no backlight so as ReeceyBurger123 says the leds would need to be checked out.Willing to help but I'm no expert.Comment
-
Full-time computer repair tech (10am - 6pm) and full-time, (8am - 11pm), Ruby on Rails DeveloperComment
-
Re: Polaroid P40LED13 powers up then shuts down
That sounds normal to me lol, also if you dont want to I would buy it off you haha
Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: Polaroid P40LED13 powers up then shuts down
as im going through the threads on here one minute i feel i have an answer for my problem and then i feel more confused lol. My set stays on for 3mins then backlight shuts off, i can see image with torch. Some say its c525 or (c252). I changed for another spare 17ips20, however, no backlight came on, image with torch visable. The spare 17ips20 was a little different though. Im stuck, i dont want the risk of removing screen etc to test the backlights unless i really have too. Panasonic tx 55c400bComment
-
Re: Polaroid P40LED13 powers up then shuts down
make sure the part numbers of the 17ips20 is a match as there is many different versions - part no is on the barcode starts as 23xxxxxx etcComment
-
Re: Polaroid P40LED13 powers up then shuts down
'17ips20' is the blank circuit board P/N, the blank board can be stuffed hundred ways to make a bunch of the PCB assembly for the needed TV models, numbers on the bar code is for the PCB assembly that you need to match.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Polaroid P40LED13 powers up then shuts down
So with the original board in this morning tv is on for 6 mins before backlight shut off, leaving tv on visible with torch, and the second time back light shut off after 3 mins. Backlights do light up with led tester on main backlight socket. Something is making a little noise/ buzzing/ high pitchComment
-
Re: Polaroid P40LED13 powers up then shuts down
Turn the backlights down as low as you can (not the brightness) and see if they stay on longer or even remain on. If that's the case then it is looking like an led(s) problem.Willing to help but I'm no expert.Comment
-
I have a Dell E5470 that powers up and boots windows no problem. Using a non-standard universal type charger, it shuts down immediately if moved, (power short in that charger or AC power jack) because the battery has no charge and isn't charging orange/white lights blinking on the front. When first powered up, BIOS power alarm stated that it could not detect the voltage setting and I had to dis-able the message to get past this. It got into Windows fine, as long as not moved, so I dis-assembled it looking for a cold solder joint on the power jack that I thought might be lifting off the MB, but... -
Hi guys have an issue with a friends labtop that has no signs of liquid damage.They said it just stopped turning on.When i press the power button it turns on normally like 35-500millamp draw and it posts and i have picture. But like after 4 seconds after it posts an image it shuts off completely.If i press power button again same thing happens. Did all basic troubleshooting with the motherboard like fresh thermal paste with it completely out the chasis with battery disconnected. Thermal camera shows these two mosfets heating up more than anything else when i press the power button.I have provided... -
I've got a Dell Latitude 5580 which came in for no power. It's not exactly a no power issue though. The battery was puffy so I replaced that, but the symptom is that when the power button is depressed, the keyboard backlights will come on for about 10 seconds then go back off. Before depressing power button, I am drawing 112ma and oddly, there is no change in current draw once the button is pressed and the keyboard backlights illuminate.
Any ideas? -
The model is 15ec-1061nm
Board number is DAG3EDMB8D0
SO i turn the laptop on , and as soon as it starts booting from disk, from usb, windows,linux,HBCD,anything i boot it just turns off....while in bios menu or in linux boot menu it stays on normally...It's like when it starts to use graphics it shuts down...But i measured 0.72V while working on the GPU power line,no excess heat is comming from GPU or CPU, i even removed the heatsink and turned the laptop on and everything worked fine, got a bit hot, fan span to full speed, but it worked like that for few minutes in bios...10-29-2024, 12:05 AM -
Hello all,
I'm stumped on this guy, so wanted to see if anyone has any further ideas:
Intro:
This is an Acer Nitro 5 AN515-55-55M1 with unknown prior history (bought "as-is" on eBay). It charges the battery and powers on from both AC adapter and battery, so I think this rules out main power issues.
Upon attempt to boot, it will "reboot" (meaning powers down and then powers on again) only once, and then stays stuck in a status of lights on / no post / no monitor. Powering on with fn+esc maxes out the fans on first boot attempt,...
Comment