-
-
Re: Eeprom dump thread!
Need help guys.. need dump files of TCL- 43D2913D LED TV attached is the original bin files. thanks in advance..Never stop LEARNING because life never stops TEACHING!Comment
-
Re: Eeprom dump thread!
I finally got around to getting the dump!
I the chip is a Winbond 25Q32JVIG but that chip is not specifically supported so I used W25Q32FV instead. Attached is the dump from that read. Would someone please have a look a fix it for me? If I didnt read it right please let me know what I did incorrectly and I will sort it out ASAP. Thank you !Comment
-
Re: Eeprom dump thread!
hi,
Medion/vestel
X14903
MD-32030
49"
BOARD: 17MB130P 23462734 ?V3(NOT SURE) ser.nr.7970800
PANEL: VES490QNDL-2D-N31 (LG32)
PS: 17ips72
hope u rescue me.
thank u in advance
greetzComment
-
Re: Eeprom dump thread!
Got another one for you good people.
Samsung UN55HU8550
Bootloop at Startup "SmartTV" logo.
I found 2 chips but I am not sure which one is the firmware so Im including both.
Both were relatively close to the processor and both were marked with a marker at the factory.
Thank you in advance!Comment
-
Re: Eeprom dump thread!
You are amazing Sir.
Thank you for the knowledge.
I will proceed accordingly.
Any hope for the panel dump in Post #1412?Comment
-
Re: Eeprom dump thread!
The dump is from the LCD Panel board of Samsung UN55MU800.
The display panel's number is CY-SM055FLLV6H.
The LCD panel board that this W25Q32JVIG resides on is BN96-41982A (see attached picture).
It is believed that there is an issue with it as the panel is not getting picture but the mainboard is believed to be good and there are no shorted components on the LCD panel board.
Thank you very much!Attached FilesComment
-
-
Re: Eeprom dump thread!
There is nothing special in it and does not affect the image (correction of broken pixels is set at the factory for each panel and the contents are different for them), the T-con firmware can be responsible for the image, it is located on the 25Q80 motherboard.Comment
-
Re: Eeprom dump thread!
I very much appreciate the guidance Lotas. It was suggested that this maybe a source of my No Picture problem.
Are you able to check my EEPROM dump in post #1414 to see if it is in order?
That would be another unknown i cam eliminate as a source of my issues.Last edited by KYBOSH; 01-23-2023, 11:45 PM.Comment
-
Re: Eeprom dump thread!
I have this corrupted Blaupukt 32 147I-GB-5B-HBKUP-UK screen LVW320SSDX E2 V1 main TP.MSD309.BP85 C12415 that will not turn on could someone have a look at it for me and see where the corruption is please? I see Lotas has the relevant skills to do this.
I am going to try and work out how to do this in future so any tips would be appreciated in working it out as I try to understand and resolve problems myself.
Thanks
Comment
-
Re: Eeprom dump thread!
Hello, there was no time, dump is ready (there was a problem in it), try it.I have this corrupted Blaupukt 32 147I-GB-5B-HBKUP-UK screen LVW320SSDX E2 V1 main TP.MSD309.BP85 C12415 that will not turn on could someone have a look at it for me and see where the corruption is please? I see Lotas has the relevant skills to do this.
I am going to try and work out how to do this in future so any tips would be appreciated in working it out as I try to understand and resolve problems myself.
ThanksComment
-
Re: Eeprom dump thread!
Ok.Comment
-
Re: Eeprom dump thread!
I need bin file for TV Westinghouse Model: DWM32H1G1 using chip MSD3393LUM, attached is the broken bin file, ThanksComment
-
-
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... -
Comment