Sharp LC-40LE810UN question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mattstolte
    Badcaps Veteran
    • Dec 2013
    • 612
    • usa

    #281
    Re: Sharp LC-40LE810UN question

    anyone?

    Comment

    • rievax_60
      Badcaps Veteran
      • May 2012
      • 897
      • australia

      #282
      Re: Sharp LC-40LE810UN question

      The back light began to flicker. I found opto PC7701 to be temperature sensitive.
      It seems that the optos in these power supplies are from a dud batch. I suggest that all four of them need to be replaced. I left the resistor mod in place.
      I have rarely seen optos fail for their own reasons.

      Comment

      • iuliantv
        Member
        • Aug 2009
        • 35
        • Romania

        #283
        Re: Sharp LC-40LE810UN question

        Originally posted by olegi
        Don't do shorting pins .Can you desolder that chip .Power up with removed eeprom chip.Tell what is the blinking code.What i think after a few unsuccess power ups (errors ) , firmware write code in this chip to prevent from further power on(may be for safety )
        Hi everyone, I have a similar problem with a Sharp LC-40le810e, front LED flashes 2 times and break and flashing 2 times, and so, according to the service manual,, Flashes 2 times 2 Power supply error (* 2) UR + 13V error,, really I lack this tension, though I try to remove EPROM memory, but do not realize is this memory, all have a strange notation,, ic2004 (denoted by 402m 40b2) 5001 IC (24lc21ai) thank you

        Comment

        • iuliantv
          Member
          • Aug 2009
          • 35
          • Romania

          #284
          Re: Sharp LC-40LE810UN question

          Originally posted by iuliantv
          Hi everyone, I have a similar problem with a Sharp LC-40le810e, front LED flashes 2 times and break and flashing 2 times, and so, according to the service manual,, Flashes 2 times 2 Power supply error (* 2) UR + 13V error,, really I lack this tension, though I try to remove EPROM memory, but do not realize is this memory, all have a strange notation,, ic2004 (denoted by 402m 40b2) 5001 IC (24lc21ai) thank you
          I took ic2004 (denoted by 402m 40b2) the same error, I think IC5001 (24lc21ai) has something to do with this error because it is located in the hdmi I tried starting the service mode with the following variants STBY and V-, STBY and V + and p + STBY, STBY and p- without result

          Comment

          • iuliantv
            Member
            • Aug 2009
            • 35
            • Romania

            #285
            Re: Sharp LC-40LE810UN question

            no idea ?

            Comment

            • rievax_60
              Badcaps Veteran
              • May 2012
              • 897
              • australia

              #286
              Re: Sharp LC-40LE810UN question

              It is difficult to follow your problem. Did you rule out the PC7703 opto?

              Comment

              • Krebstar
                New Member
                • Oct 2015
                • 6
                • United States

                #287
                Re: Sharp LC-40LE810UN question

                Hello,

                Some searching via google has led me to this thread. Not to post hijack, but there don't seem to be many threads about this set. I also have the LC-40LE810UN Tv. For a few months now the set will work just fine. Then, after 5 minutes or so the back light will begin to flicker ( much like an old neon tube). Its more of a sporadic flicker ( different intensities) then a steady pulsing.

                It happens on every input regardless if it is receiving a video signal or not. When I go to turn the Tv off, the screen ( not the 'V') flashes 6 times slowly. I cannot find any information on this particular blinking. Most people with issues seem to have the 'V' blinking error codes. There isn't even a 6 blink code in the service manual ( that I saw).

                Can anyone offer any suggestions? I'm fairly handy with electronics and such If I know where to look. Power issues? Over heating?

                Also, can anyone translate the directions on how to enter the adjustment process mode ? What does "Before entering the adjustment process mode, the AV position RESET in the video adjustment menu" mean? Do I need to just highlight reset or do I need to actually reset the input? Kind of confusing. I was going to check the menu to see if any errors are listed.

                Thanks for any help !

                Comment

                • rievax_60
                  Badcaps Veteran
                  • May 2012
                  • 897
                  • australia

                  #288
                  Re: Sharp LC-40LE810UN question

                  I found the instructions confusing also. I remember making sense of it, I don't fully remember the details now.
                  Most are developing a shutting down problem with 2 flashes of the standby LED. This is caused by optpo-coupler PC7703 in the AC_DET circuit gradually losing gain. My TV had this problem first. I fixed it by reducing the resistor on the its LED side.
                  The TV then developed a flickering problem a few months later. I found another failing opto in the back-light circuit. At this stage I decided to replace all 4 optos.

                  Comment

                  • Krebstar
                    New Member
                    • Oct 2015
                    • 6
                    • United States

                    #289
                    Re: Sharp LC-40LE810UN question

                    Originally posted by rievax_60
                    I found the instructions confusing also. I remember making sense of it, I don't fully remember the details now.
                    Most are developing a shutting down problem with 2 flashes of the standby LED. This is caused by optpo-coupler PC7703 in the AC_DET circuit gradually losing gain. My TV had this problem first. I fixed it by reducing the resistor on the its LED side.
                    The TV then developed a flickering problem a few months later. I found another failing opto in the back-light circuit. At this stage I decided to replace all 4 optos.
                    Thanks for your quick response. I plan on taking a look at the boards this weekend. Maybe Ill just replace to opto and go from there. Is there a schematic floating around somewhere? Thanks again !

                    Comment

                    • rievax_60
                      Badcaps Veteran
                      • May 2012
                      • 897
                      • australia

                      #290
                      Re: Sharp LC-40LE810UN question

                      The local TV repair guy says that the power supply schematic is often not included in TV service manuals as it isn't with this one.

                      Comment

                      • budm
                        Badcaps Legend
                        • Feb 2010
                        • 40746
                        • USA

                        #291
                        Re: Sharp LC-40LE810UN question

                        Power supply board is made by DELTA (DPS-126CP) so it is not allowing Sharp or other companies to release the diagrams.
                        Last edited by budm; 10-23-2015, 02:54 PM.
                        Never stop learning
                        Basic LCD TV and Monitor troubleshooting guides.
                        http://www.badcaps.net/forum/showthr...956#post305956

                        Voltage Regulator (LDO) testing:
                        http://www.badcaps.net/forum/showthr...999#post300999

                        Inverter testing using old CFL:
                        http://www.badcaps.net/forum/showthr...er+testing+cfl

                        Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                        http://s807.photobucket.com/user/budm/library/

                        TV Factory reset codes listing:
                        http://www.badcaps.net/forum/showthread.php?t=24809

                        Comment

                        • Krebstar
                          New Member
                          • Oct 2015
                          • 6
                          • United States

                          #292
                          Re: Sharp LC-40LE810UN question

                          Opened my tv up today to inspect things. I think Im just going to replace all the optos since they ( form what Ive read) seem to be the likely suspect. Does anyone have a source for these optos? My usual electronic suppliers don't seem to carry them. Is there a comparable alternative?

                          Cosmo
                          1010
                          817
                          K10
                          H

                          Comment

                          • Krebstar
                            New Member
                            • Oct 2015
                            • 6
                            • United States

                            #293
                            Re: Sharp LC-40LE810UN question

                            So after taking the back off, I have been running the tv for about 8 hrs now with no back light flicker. Could it be the set was over heating with the back on? I that would explain why it wouldn't flicker right away, but after 5-10 minutes or so. I noticed there are no vent holes above the power board on the back of the case. Why would they do that? Seems that component would be sensitive to heat.

                            Comment

                            • budm
                              Badcaps Legend
                              • Feb 2010
                              • 40746
                              • USA

                              #294
                              Re: Sharp LC-40LE810UN question

                              Opto is also sensitive to heat.
                              Never stop learning
                              Basic LCD TV and Monitor troubleshooting guides.
                              http://www.badcaps.net/forum/showthr...956#post305956

                              Voltage Regulator (LDO) testing:
                              http://www.badcaps.net/forum/showthr...999#post300999

                              Inverter testing using old CFL:
                              http://www.badcaps.net/forum/showthr...er+testing+cfl

                              Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                              http://s807.photobucket.com/user/budm/library/

                              TV Factory reset codes listing:
                              http://www.badcaps.net/forum/showthread.php?t=24809

                              Comment

                              • rievax_60
                                Badcaps Veteran
                                • May 2012
                                • 897
                                • australia

                                #295
                                Re: Sharp LC-40LE810UN question

                                I noticed that the faulty optos were temperature sensitive. Symptoms became worse with increasing temperature. The 817 opto is manufactured by more than one manufacturer.
                                I pulled mine out of a junked plasma power supply.
                                There is a bothersome aspect to choosing new parts. There is a wide range in the Current Transfer Ratio spec for the various suffix codes. https://cdn.badcaps-static.com/pdfs/...7b665a5160.pdf
                                In most circuits the CTR doesn't matter much, so long as it's high enough. I noticed that the opto(PC7701) in the back-light circuit has a trim pot across the LED side. This can only be to adjust for the optos CTR. I would try to get the K817P3.

                                Comment

                                • Krebstar
                                  New Member
                                  • Oct 2015
                                  • 6
                                  • United States

                                  #296
                                  Re: Sharp LC-40LE810UN question

                                  So what are your thoughts about cutting away the back case above those optos to improve air flow? Do you think it would be worth it? I mean the set is working great now. So much so Im debating even putting the case back on .

                                  Comment

                                  • rievax_60
                                    Badcaps Veteran
                                    • May 2012
                                    • 897
                                    • australia

                                    #297
                                    Re: Sharp LC-40LE810UN question

                                    That is not a good idea. You could adjust the trim pot that is across the LED side of the opto. There are 2 pots. You will have to look at the print to see which is the correct one. Measure the resistance before you move it so you can put it back to the same setting later.

                                    Comment

                                    • rievax_60
                                      Badcaps Veteran
                                      • May 2012
                                      • 897
                                      • australia

                                      #298
                                      Re: Sharp LC-40LE810UN question

                                      This is the data PDF for the Cosmo opto. Try to work out what the CTR spec is from the info in page 4.

                                      Comment

                                      • Krebstar
                                        New Member
                                        • Oct 2015
                                        • 6
                                        • United States

                                        #299
                                        Re: Sharp LC-40LE810UN question

                                        Originally posted by rievax_60
                                        That is not a good idea. You could adjust the trim pot that is across the LED side of the opto. There are 2 pots. You will have to look at the print to see which is the correct one. Measure the resistance before you move it so you can put it back to the same setting later.
                                        Excuse my ignorance, but what does adjusting the pot actually do? Once I dial it in is it something I can leave alone? Why would I need to 'put it back to the same setting later'?

                                        Comment

                                        • rievax_60
                                          Badcaps Veteran
                                          • May 2012
                                          • 897
                                          • australia

                                          #300
                                          Re: Sharp LC-40LE810UN question

                                          Originally posted by Krebstar
                                          Excuse my ignorance, but what does adjusting the pot actually do? Once I dial it in is it something I can leave alone? Why would I need to 'put it back to the same setting later'?
                                          Adjusting the pot might compensate for the reduction of CTR that the original optos seem to suffer from. This loss of CTR is what causes the AC-DET problem and the instability of the back-light power control loop.
                                          It is always a good idea to note the original position of things before they are moved. In this case it might be decided to put the pot back to the original position after the opto is replaced.

                                          Comment

                                          Related Topics

                                          Collapse

                                          • howardc64
                                            A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
                                            by howardc64
                                            Problem

                                            This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
                                            08-04-2024, 10:36 PM
                                          • sam_sam_sam
                                            Lift Master Garage Door wall switch display / motion sensor controller display disappeared no back light
                                            by sam_sam_sam
                                            This happened last Saturday and today I finally had time this morning before I went to work to replace two non brand capacitors

                                            I will let you be the judge weather or not these are bad or not according to the blue ESR meter that I am using

                                            I am comparing them to a brand new one that I installed

                                            The display came back on and the programming was not lost which I was surprised by I would have thought that when the display went blank that so did the memory as well

                                            I going to let it run for several days before I remount back on the wall next to the...
                                            09-05-2024, 06:48 PM
                                          • Document Archive
                                            HP ProDesk 600 G5 + APC Back-UPS 700VA ProDesk 600 i7-9700 Specification for Upgrade or Repair
                                            by Document Archive
                                            This specification for the HP ProDesk 600 G5 + APC Back-UPS 700VA can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the ProDesk 600 G5 + APC Back-UPS 700VA boardview and ProDesk 600 G5 + APC Back-UPS 700VA schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties...
                                            09-12-2024, 02:30 PM
                                          • Document Archive
                                            HP ProDesk 600 G5 + APC Back-UPS 700VA ProDesk 600 i5-9500 Specification for Upgrade or Repair
                                            by Document Archive
                                            This specification for the HP ProDesk 600 G5 + APC Back-UPS 700VA can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the ProDesk 600 G5 + APC Back-UPS 700VA boardview and ProDesk 600 G5 + APC Back-UPS 700VA schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties...
                                            09-12-2024, 02:30 PM
                                          • Document Archive
                                            HP ProBook 430 G7 + APC Back-UPS 700VA Notebook 400 Specification for Upgrade or Repair
                                            by Document Archive
                                            This specification for the HP ProBook 430 G7 + APC Back-UPS 700VA Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the 430 G7 + APC Back-UPS 700VA boardview and 430 G7 + APC Back-UPS 700VA schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that...
                                            09-06-2024, 08:10 PM
                                          • Loading...
                                          • No more items.
                                          Working...