Hi, I picked up a Sharp Aquos LC-26DV22U for $20 at a garage sale. Figured I would find some puffed up caps and replace them for $5. No such luck. I hit the power button and the light turns green on the front. No picture, backlight or sound. I do hear some buzzing noise from the large transformer on the p/s board (CEF273A). After reading that pins 1-5 on the white connector (far left) needed 24v and they only had about 8v, I wondered what would happen if I 'introduced' 12v from a wall wart. Well, I touched pin 1 (red wire) with the 12v adapter and now the TV & DVD work fine! The noise from the transformer goes away, too. Could this transformer be going bad or would another component keep it from working properly? Thanks for any suggestions.
26" Sharp LC-26DV22U LCD power problem.
Collapse
X
-
Re: 26" Sharp LC-26DV22U LCD power problem.
Do you hear a slight ticking or clicking sound from the transformer?
Do you ever hear a relay click when the power button is pressed?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search. -
Re: 26" Sharp LC-26DV22U LCD power problem.
Have you tested the small green fuse top of your picture to the left of the yellow barcode labelPlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
The sound I hear from the transformer is buzzing sound (or maybe a sizzling sound). When I power-on, the relay clicks right away. When power-off, there is a 10 second delay before relay clicks.
The green fuse tests good (I did a continuity test with my meter).Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
OK, try unplugging the power connector where you measure 24V and see if it increases.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
OK, With green light on, pins 1-5 measure 8.74v whether connector is plugged in or not. After I 'jump start' it, unplugged they measure about 25.3v. Plugged in, voltage drops about 1/4v. Why would 'jumping' it with 12v for about a second make it work? Some facts I didn't state earlier: all the caps are Rubycon and the set was made in March 2007. Thanks!Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
Where exactly do you connect the Booster ? 12v+ to pin and what for the ground?
When it doesnt come on can you locate the startup cap in the primary section maybe
50v 68uF and see what voltage it has.
EDIT could be C431 50v 10uFAttached FilesLast edited by selldoor; 08-22-2012, 09:31 AM.Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
I connect the booster pos. to any of the first 5 pins and the neg. to a mounting screw. Doesn't matter which pin - results are the same. The closest cap I could find is a 100uf/100v and it reads .3v - if I'm measuring it right. I put the pos. lead on one side of the cap and the neg. lead on a mounting screw. Did I do that right?Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
No - just measure across the cap what value is c431 did you miss my edit
What do they measure after you have boost startedPlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
Sorry, I missed it. After I downloaded it then found a rar reader and finally opened it - I realized I already had the schematic printed out! The CEF273A in your doc is a little different than mine. I had downloaded the manual for a LC26SH12U set and it more matches my board. Anyway, I tested the C431 and found the voltage was 19v before my boost and 15.45v after.Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
Can you get a picture of the back of the board - perhaps a poor joint. In fact
before you do that, while its in the non start stage, try just pressing gently on the board with a stick or piece of plastic just to flex it here and there- try near the connector and around the transformer.
You could also try gentle heat with a hairdryerPlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
Well, I poked and prodded the whole board. I did notice the sound of the buzzing changed on the transformer when I prodded it. No change to voltages though. I touched each joint on the big transformer with a soldering iron with no results. I didn't try the hair dryer but earlier, I had left the TV on for about 2 hrs to play a DVD. Everything was nice and hot, but still no 25v when I tried to turn it back on. Attached are two pics of the back.Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
OK, I look at both power supply diagram, so the switched 24V (PIN1~5) is only putting out about 8V. What do you get at the switched 12V output? The 12V and 24V are generated by the same power transformer, so I expect the 12V output will be really low. So when you attach the external 12V to feed into the 24V line, the backlights and the TV and sounds start working?
And right now you have indicated that the TV is still running with and external power supply attached but you are still not getting the 24V for inverter circuits, that is confusing since the backligts inverter circuits need 24V to operate. May be I do not quite understand what you are seeing as far as the voltage readings you are seeing? How big is this 12V power supply? The 24V supply in the TV is about 4~5A.
I cannot really see how the TV is running off the 12V feeding into the 24V output terminals right now.Last edited by budm; 08-22-2012, 06:54 PM.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
No, I'm not attaching the 12v wall wart permanently. I put a couple of leads on the wall wart and briefly (1 second) touch it to pin 1 on the white 24v connector. This makes that pin (and pins 2,3,4,5) go from 8v to 24v. Then, the TV works fine. It's like I "jump start" it. The only other voltage I've checked it the connector that goes to the DVD. It was about 3v before my "jump start". After, it was 12v.Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
When I said I wasn't getting 24v, I meant that after I shut the TV off and then turned it back on, I wasn't getting 24v. Every time I shut off the TV, it won't work when I turn it back on - unless, I jump start it with the 12v AC adapter.Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
OK, now I understand, let me see how the circuits work indetails then I may be able to help.
So I can use the LC-26SH12U circuits to analyze the problem? The one that I posted?Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
Did you replace any caps?- looking at c431 on the back the joints dont look too good.
What make of cap is that? There are other odd looking parts perhaps budm will identify where we should be concentrating onPlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: 26" Sharp LC-26DV22U LCD power problem.
Replaced it with what make/series - should be low esr - can you check the soldering - probably looks worse in the pic than it is but the joints look pretty close together and the trace looks a little lifted.Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
Related Topics
Collapse
-
by theone111I have an LG Plasma TV 60PM6700 for the past ~12 years.
In the last ~3-4 months I have been having some issues.- Problem: It started with random picture disappearing (sound still worked).
Frequency: Happened about once a week.
Solution: Had to turn off TV wait a few seconds before turning it on again. - Problem: Then it got worse and the TV started to shut down and when turning on the no picture just sound.
Frequency: Happened about once a week.
Solution: Had to turn off TV wait about 10-20 seconds and turn it on again to solve. - Problem: TV shuts down
1 Photo - Problem: It started with random picture disappearing (sound still worked).
-
by DuranitronWhen I reflash again the bios of hoaca388 the unit powers on and the unit lives!!! Hooray!! All voltage in the coil 3.3v, 5v and 6.7v indicate charging are all present. including the cpu voltage , EEPROM and GPU voltage the unit is now alive, normal screen booting to windows and log in screen until I power it off. Then the unit never goes on even when pressing the power button in the keyboard.. Voltage reading 19v main , 3.3v VCC in IT8225E-128 and EEPROM VCC 0 volt and the charging voltage 0 volt.
Try to trace the power switch button goin to the power switch IC PU8803 (APL3533AQBI-TRG)... -
by EazyBoneHello, trying to fix C9 55 inch. I have pulled the back and all looks completely normal with nothing burnt so far. This is first time attempting to fix a tv so any help is appreciated.
Problem. I hit power button, red light on TV turns off and tries to turn on, no picture shows up and then shuts off. This occurred after house power turned on and off, not from a storm.
I have tested the power going from power supply to main board, all 12v and 20 volt readings are proper when I hit power button.
The power supply to t con is different story.
This... -
by Dr.dI have a lenovo ideapad 5 14itl05, board LA-K321P, That will only power up on Battery only, or with battery disconnected and power adapter only. If battery is connected and usb-c power plug connected. It only works on battery and will not charge. I can however force it to charge by connecting the battery from a disconnected state while the power USB c plug is powering the laptop.
Additionally....to add to this strange situation. The usb-c power plug ONLY works to power the laptop on one side when inserted into the boards power usb c plug. If you rotate it 180 degrees, the board gets... -
I just picked up a Sharp LC-80UQ17U here in Denver on Craig's. The previous owner said he was watching it and "pop" it stopped. Opened it up to find a blown fuse on the high Voltage side of the PS. I bypassed it with a 7.5 Ampere automotive fuse and saw a flash in component NTC7001 (as the fuse popped). I am not going to try to apply any more power to the board until I can locate a schematic. Does anyone have the schematics to RUNTKB217WJQZ?
... - Loading...
- No more items.
Comment