Re: Cougar CMX 700W suddenly Went off
Was talking about a 20w watts though
Was talking about a 20w watts though
-
-
Re: Cougar CMX 700W suddenly Went off
Told you check d10 out of the circuitComment
-
Re: Cougar CMX 700W suddenly Went off
Check the others tooComment
-
Re: Cougar CMX 700W suddenly Went off
Just found dark brown here too !!Attached FilesComment
-
-
Re: Cougar CMX 700W suddenly Went off
Took it off, a short can make the PSU to shut offLast edited by Drack; 01-18-2017, 04:40 PM.Comment
-
Re: Cougar CMX 700W suddenly Went off
The fan ticks or makes something when you short ps on with ground or just dead?
Drack.[/QUOTE]
Just dead FanComment
-
Re: Cougar CMX 700W suddenly Went off
change all small caps.Comment
-
Re: Cougar CMX 700W suddenly Went off
Changed all capacitors
Still nothing .
What about the secondary supervisor ? What should i do on it ?Last edited by abdorefky; 04-02-2017, 11:25 AM.Comment
-
Re: Cougar CMX 700W suddenly Went off
green corrosion behind q202.
dammed brown glue ate a trace.Comment
-
Hi do you still got that psu , I have the same model and I need the marking on that transistor
Comment
-
OK. I got the rocker switch figured out thanks to the good advice on this forum.
Now I need to figure out the correct wire to go to the switch from the broiler element and from the oven element.
This is a Whirlpool RDE3340 electric range.
The common wire on the switch appears to have a high temperature insulating material. I am guessing that both the wire to the broiler and the wire to the oven elements also need relatively high temperature insulation. What do I need to look for? The broiler is rated at about 2400 watts.
Where may I find parts... -
We have an Lenovo Yoga 710 15ISK that we use as a secondary laptop. To cut a long story short, around May 2023, while traveling, I connected the laptop into an electrical outlet that was already switched on. Something made a "pfft" sound and the laptop refused to turn on after that. After getting back home, I gave the the laptop for repair to an informal repair person. He replaced the adapter and an internal motherboard part, but after he returned it I noticed that the LCD did not look normal. Essentially, every alternate horizontal line on the screen had gone missing. The laptop was... -
I currently have a customer's vintage fan on the work bench to repair.
It uses an induction motor with 4 poles. One of the poles is open.
I couldn't find the break so i cut off the original wire.
I have measured the other poles and the resistance is about 28 ohms per pole and I measured the diameter of the wire with my digital calipers and it is 0.35mm in diameter.
I need to work out how much 0.35mm diameter enamelled copper wire i need to order for it to be 28 ohms. I have used this calculator and it says i need 160.35 metres.
The enamelled copper... -
I was Ollie today which is a close out / surplus outlet store I do not go in there to often because you find things that you should not be tempted by but that is a another story
I saw a small space heater that used a wire type of heater element which I been looking for a while but not really hard mind you but when I saw this I grabbed it I going to go back tomorrow and buy the last one that is like the one I bought today because I need the heater element and the ceramic insulators and more of heat element wire because this one has two different wattage settings one 1300 watts ( tap... -
I got this recently as-is. Gigabyte 1070 video card.
DVI port is removed. I don't know why.
A wire is soldered across two spots where it looks like the DVI port was. I don't know why.
I've read of people simply ripping out DVI ports and the rest of the cards still working fine. Never read anything about soldering a wire in there for some reason.
The card seems to work fine, except it's stuck in low clock speeds. While starting a game or benchmarking, the clocks may momentarily increase to around where they should be, then goes way back down and stays...
Comment