Re: Dell E153FPB Back Light problem
Reseat and clean all your connectors with isopropyl alcohol.
Dell E153FPB Back Light problem
Collapse
X
-
Re: Dell E153FPB Back Light problem
I have a E153FPB with a blurry display. I am not sure where to start because it is only blurry with the VGA input. If I have a signal coming in and click the menu button, the menu looks fine, but the backgroud VGA input is blurry. It almost looks like I can see the progressive scan. My first guess is the actually logic board for video input. What do you guys think... thanks for the helpLeave a comment:
-
Re: Dell E153FPB Back Light problem
Hello & Happy New Year To All,
Can anyone give me a pinout for CN701 on the e153fpb (48.L0H02.A00).
I'd like to test for output voltages to logic board.
Thanks In Advance,
lcdmanLeave a comment:
-
Re: Dell E153FPB Back Light problem
Repair kit arrived yesterday and after re-soldering all four Xformers (bent the leads out for better electrical / mechanical connection) and replacing two c5707 Xsistors it is back up and running. Will burn it in for a day, but so far so good.
Many thanks to the forum and all those who've contributed here!Leave a comment:
-
Re: Dell E153FPB Back Light problem
There were only four c5707s (two bad, two good). Did not see fu9024 but the other transistors seem to check out.
Thanks!Leave a comment:
-
-
Re: Dell E153FPB Back Light problem
1) You MUST resolder all the inverter transformer pins due to poor quality solder/soldering. A visual inspection may seem fine, but you MUST resolder them.
2) Check all c5707s and fu9024s for shorts.Leave a comment:
-
Re: Dell E153FPB Back Light problem
If you add a photo, perhaps we can see if it is an E173 OR an E153, which you have filed this under ???Leave a comment:
-
Re: Dell E153FPB Back Light problem
New member here (2nd post).
I'm working on a Dell e173fpb that would not power up. The power switch/light would repeatedly blink and each time you could see a short burst of backlighting from the lower-left corner (two clues).
After pulling it apart, giving the boards a visual once-over and finding this post I checked the fuse (FP751) which seemed fine (jumping it caused no change). Next I tested the Q7x0 and Q7x9 transistors and found two (same side) that seemed shorted. After desoldering them I now have a monitor that functions on two lamps but only for a few seconds (screen appears then monitor shuts off, restarts OK). I've ordered a repair kit and will try to come back with an update after I've replaced the two transistors.
A close visual inspection of the boards (both sides) reveals nothing out of place. I'm about half-way through reading this thread so there may be some nuggets that I haven't found yet.
Anything else I should check while I'm waiting?
Cheers and thanks everyone!Leave a comment:
-
Re: Dell E153FPB Back Light problem
Reflowing applies to another kind of problems,mostly with BGAs.
And don't worry about the "great resistance" thing.Here besides helping each other,we have fun....
And about the non-English native thing,don't worry...My native language is Spanish and I've managed to get along pretty well so far (I think) ....Leave a comment:
-
-
Re: Dell E153FPB Back Light problem
Hi again,
Thanks for the advice. I will do that.
i was thinking about doing a reflow of the solders using a heat gun (using my infrared thermometer to gauge temperature of the PCB). I fixed an IBM laptop that way (the one I'm using to type this).
Best regards,
Eric
ps. Sorry about the picture and the 'great resistance' thing was not meant to be funny, I am not a native english speaker and things can get warped in translation. I meant infinite resistance.
e.Leave a comment:
-
-
-
Re: Dell E153FPB Back Light problem
Hi all,
I just wanted to share my experience:
My father-in-law had a Dell 153FPB that 'died', i.e. had no backlight.
I saw it flash a bit when I plugged it in so I decided to google a bit to see if these things had a common point of failure (usually bad caps in my experience).
Fortunately, I read this forum and that pointed my attention to the PF751 fuse, not very obvious for an amateur like me I must confess.
I measured great resistance over the PF751 fuse, an indication of a blown fuse, so I replaced it with a 2A slowblow fuse and lo and behold!
We have a backlit image again! I hope the new fuse holds.
Thanks for the groundbreaking work,
Eric Benedikz
ps.saw this picture of the culprit:
For future reference, note the links in my signature on the proper way to attach pictures.
PlainBillLeave a comment:
-
Re: Dell E153FPB Back Light problem
Hi all,
I just wanted to share my experience:
My father-in-law had a Dell 153FPB that 'died', i.e. had no backlight.
I saw it flash a bit when I plugged it in so I decided to google a bit to see if these things had a common point of failure (usually bad caps in my experience).
Fortunately, I read this forum and that pointed my attention to the PF751 fuse, not very obvious for an amateur like me I must confess.
I measured great resistance over the PF751 fuse, an indication of a blown fuse, so I replaced it with a 2A slowblow fuse and lo and behold!
We have a backlit image again! I hope the new fuse holds.
Thanks for the groundbreaking work,
Eric Benedikz
ps.saw this picture of the culprit:
http://s807.photobucket.com/albums/y...g=Dell+E153FPBLeave a comment:
-
Re: Dell E153FPB Back Light problem
hi tnx for the reply.. can you tell what is the proper way of checking the bulbs? another problem i encountered is that I cannot push the button while the lcd is on this mode.. It only took seconds to turn on and off.. then long minutes on then off againLeave a comment:
-
Re: Dell E153FPB Back Light problem
Hi Folks I'm New here I need help regarding may Dell E153FB.. I've been working on my monitor for almost 3 days.. I tried all i have read from this forum like changing the 4 transistors, resoldering the transformers and other components, and changing the fuse.. It's just that it still keep on turning on and off.. Any possible solution you can give guys? thanks in advanceLeave a comment:
-
-
Re: Dell E153FPB Back Light problem
Have you checked the "bulbs"?
If its turning on and then abruptly turning off then you might want to check the bulbs.Leave a comment:
Related Topics
Collapse
-
by sam_sam_samThis happened last Saturday and today I finally had time this morning before I went to work to replace two non brand capacitors
I will let you be the judge weather or not these are bad or not according to the blue ESR meter that I am using
I am comparing them to a brand new one that I installed
The display came back on and the programming was not lost which I was surprised by I would have thought that when the display went blank that so did the memory as well
I going to let it run for several days before I remount back on the wall next to the... -
by multimesutHello friends,
A yellow light was flashing on my monitor. It was like it was constantly cutting power. When I opened it up, I saw that the big capacitor in the high voltage line was leaking. I replaced it. When I turned it on for the first time, it had the same problem again. But then, interestingly, it got better. The yellow light was on steady. But the monitor wouldn't turn on. When I examined them with a thermal camera, I saw that the Fli5961-LF reached 50 degrees Celsius and the EM636165TS next to it reached 100 degrees Celsius and was drawing high current on the motherboard....1 Photo-
Channel: Troubleshooting Computer Displays
11-13-2024, 07:00 AM -
-
by boyebaranhi to all
tv turn on and show logo(backlight on)than backlight turn off than red led in front blinking 7 time. the tv remote control working fine (sound on no picture).backlight changed same problem
in 65k560 how to remove protection of backlight? picture of inverter and sockets attached .
please advise me tnx4 Photos05-20-2025, 07:11 AM -
by SDNarciaHello, I have a Dell 15R-5521, with the problem that the Ctrl, Alt, Shitf and Num Lock keys do not work, I tested the keyboard with a keyboard tester and it is functional, I also got another new keyboard and the computer has the same problem with the same keys. Check continuity between the ZIF connector from the keyboard to the KBC and all pins are correct. I cleaned the ZIF connector and the KBC and I still have the same problem. I reinstalled windows just in case, and it didn't work. I updated the BIOS to the latest version A16 and there were no changes.
As additional information,... -
by Achille15Hello everyone,
so, I have this laptop Dell Inspiron N5110 with a heating problem on both CPU (I7-2680qm) and GPU (GT 525m), I tried many solutions, like changing thermal paste every month, using thermal pads on CPU and GPU, even using thermal pads on CPU nearby coils; but nothing worked, just minutes after booting the laptop shuts itself down so I thought it might be a short problem, so I decided to check what's going on, so I went online and some tutorial (general one) said to check inductors in order to find the shorted circuit, after checking (CPU removed), I found the culprit to be... - Loading...
- No more items.
Leave a comment: