Hisense LCD3233NEU - is there way to set test pattern on T-CON?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Folxs
    Senior Member
    • Nov 2016
    • 167
    • Poland

    #1

    Hisense LCD3233NEU - is there way to set test pattern on T-CON?

    Hi, I got Hisense LCD3233NEU that turns on but screen is just black with backlight - I wanted to diagnose if it is mainboard or T-CON, can I somehow set T-CON to display test pattern like in plasma TVs?

    Strange that almost all power rails are correct but between 12V_A and GND_A there are 15.5V

    I even reflashed small FLASH chip 25F40 but didn't helped - IDK if CPU is working or not.

    How to determine if it is mainboard or T-CON?
    Attached Files
  • dick_barton
    Badcaps Legend
    • Aug 2015
    • 6642
    • Wales

    #2
    Re: Hisense LCD3233NEU - is there way to set test pattern on T-CON?

    Can you connect up a scart lead to go between your set and another one. Scart wired video out to video in and video ground.
    I've never tried it so don't know if it would work.

    Have you checked that you have 12V on both sides of the fuse F1 on the Tcon
    Attached Files
    Last edited by dick_barton; 05-15-2020, 03:06 PM.
    Willing to help but I'm no expert.

    Comment

    • budm
      Badcaps Legend
      • Feb 2010
      • 40746
      • USA

      #3
      Re: Hisense LCD3233NEU - is there way to set test pattern on T-CON?

      Find out first if you do have 12vdc to run the T-CON first.
      Never stop learning
      Basic LCD TV and Monitor troubleshooting guides.
      http://www.badcaps.net/forum/showthr...956#post305956

      Voltage Regulator (LDO) testing:
      http://www.badcaps.net/forum/showthr...999#post300999

      Inverter testing using old CFL:
      http://www.badcaps.net/forum/showthr...er+testing+cfl

      Tear down pictures : Hit the ">" Show Albums and stories" on the left side
      http://s807.photobucket.com/user/budm/library/

      TV Factory reset codes listing:
      http://www.badcaps.net/forum/showthread.php?t=24809

      Comment

      Related Topics

      Collapse

      • nono34
        Hisense stuck in Colors cycle like test pattern.
        by nono34
        Hello,

        I accidentally changed the project ID in the service menu of my Vidaa Hisense 100U7KQ TV. When I turn on the TV, the screen displays an RGB color cycle (test mode???). I contacted Hisense, and they sent me a usb_MTK_9618.EU.bin file, but it doesn't work. I can see that the USB drive is being read, and it flashes for about 10 minutes (the screen remains in the color cycle during the firmware reading), then the TV turns off and restarts, but still in the color cycle mode.

        I want to mention that the 4GB USB is formatted in FAT32 MBR. I've also renamed the file to...
        10-24-2024, 04:31 PM
      • alltvrepairs
        Lg TCon test pins for screen test
        by alltvrepairs
        Hi,
        i have a 65 Panasonic TX-65HX710E using vestel 17MB170 main and Lg tcon.

        Few drops of water fell probably near COF and have no display. Tried removing tabs but no.part of display present as if tcon fuse open. However 12v is present and tcon can be felt warm enough that supplies are present. Backlight and sound ok.

        Anyone knows if this TCon 6870c-0805A has any special test pins for rgb test?

        Appreciate your help....
        06-13-2025, 06:33 AM
      • x_orange90_x
        TCL 50S535 bad tcon or panel issue?
        by x_orange90_x
        Just bought this for 10 bucks yesterday hoping to fix it. The guy said water dropped inside from a dehumidifier hose and it started showing black and white vertical bars then went blank. When I got it home and turned it on it came on fine and displayed correctly but I was noticing faint vertical bars in the image. After a little bit I turned it off and back on and it was a black screen again. I opened it up to check for water damage and corrosion but didn't find anything of the sort. I cleaned the ribbons anyway and reconnected them but still got a blank screen. If I disconnect the right side...
        03-29-2025, 11:02 PM
      • Hakuu
        LG OLED77G1PUA - No Video / Audio after a TCON Board change and Software Update
        by Hakuu
        Hi There,

        This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.

        After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.

        More Details

        TV Model - LG OLED77G1PUA

        Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt...
        07-12-2023, 02:37 PM
      • chth96
        How Can I test PWM DM0365R?
        by chth96
        Hello
        I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
        So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
        I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
        I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
        06-18-2025, 04:14 PM
      • Loading...
      • No more items.
      Working...