Announcement

Collapse
No announcement yet.

LG 32lc46 totaly dead

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Re: LG 32lc46 totaly dead

    Sm
    Attached Files

    Comment


      Re: LG 32lc46 totaly dead

      cheers mate for that

      Comment


        Re: LG 32lc46 totaly dead

        Pt 2
        Attached Files

        Comment


          Re: LG 32lc46 totaly dead

          could someone look at the pdf page 27 standby circuit 1c903
          these are the voltages i am getting
          pin 1 3.29
          pin 2 3.29
          pin 3 gnd
          pin 4 1.17
          pin 5 0.78
          its a sc156515m-1 8tr
          have checked c912 +have 3.12 volts
          right ic902
          with tab at the top
          pin 1 left 0.00
          centre 0.11
          pin 3 4.66
          az1117h-2.5tr/e1
          just worked out pin 1 is gnd
          pin 2 is output
          pin 3 is input
          still got no ledS on the front of set at all ?
          Last edited by vinceroger69; 03-23-2012, 07:05 AM.

          Comment


            Re: LG 32lc46 totaly dead

            any idea what ic902 does just looked at pdf looks like output should be 2.5 volts?
            so it looks like i have
            4.66 input
            0.11 output
            output goes to +2.5v ddr-ctz whats that?
            also where does the voltage to light the leds come from?
            Last edited by vinceroger69; 03-23-2012, 08:09 AM.

            Comment


              Re: LG 32lc46 totaly dead

              p 27
              Attached Files

              Comment


                Re: LG 32lc46 totaly dead

                right whilst i am trying to locate the correct main board i thought i would sort out the old power supply as in post 53 which budm was helping me test voltages etc right accros the capacitor as in your pdf test ponts its 13.8 volts and between the other two test points its 2.4v
                i have checked and the board still has the 2x5volts present nothing else on any of the out put voltages even with a 1k resistor as a load.

                also i cant locate the correct main board with the same ebr number on but i have found a lg42lc46 mines a lg32lc46 would you guys take a gamble on it working ok?
                as its out of a 10inch larger lcd would the picture still be ok? could i alter it in the sets on board service mode?
                Last edited by vinceroger69; 03-24-2012, 11:25 AM.

                Comment


                  Re: LG 32lc46 totaly dead

                  regarding my posts 104/105/106 has anyone got any ideas what to check now cant locate the correct mainboard at all at the minute

                  Comment


                    Re: LG 32lc46 totaly dead

                    Mainboard should be okay if model & panel is the same. Is your LCD panel an LG Philips?

                    Is there an ACD pin?
                    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                    Comment


                      Re: LG 32lc46 totaly dead

                      now your asking will take back of the set again and look for you
                      yes ac-det pin on main psu/mainboard connectors
                      Last edited by vinceroger69; 03-29-2012, 11:44 AM.

                      Comment


                        Re: LG 32lc46 totaly dead

                        tom66 not sure what the lcd panel is does not seem to say but have tested the ac-det pin 5.10 volts.

                        Comment


                          Re: LG 32lc46 totaly dead

                          right new mainboard has just arrived put it into set now i have the red standby light come on i press the remote changes to green after flashing 6 times nothing on the screen whatsoever no sound only a slight speaker pop as it comes out of standby any ideas guys all voltages on board are spot on as per board markings screen does not even flash any idea what 6 green led flashes mean?
                          this board is out of the exact model even same ebr numbers.

                          Comment


                            Re: LG 32lc46 totaly dead

                            Originally posted by vinceroger69 View Post
                            right new mainboard has just arrived put it into set now i have the red standby light come on i press the remote changes to green after flashing 6 times nothing on the screen whatsoever no sound only a slight speaker pop as it comes out of standby any ideas guys all voltages on board are spot on as per board markings screen does not even flash any idea what 6 green led flashes mean?
                            this board is out of the exact model even same ebr numbers.
                            My TV flashes LED five times when it switches on, I think that just means "warming up" or something, so try checking all your connectors are good e.g. backlight cables, T-con, power.
                            Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                            For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                            Comment


                              Re: LG 32lc46 totaly dead

                              will go and try and leave it on green standby for a bit see if it comes on with time will remove all connectors and re seat them

                              Comment


                                Re: LG 32lc46 totaly dead

                                still nothing just rechecked voltages one says 3.4-on on the psu reads 0 volts in standby 2.00 volts when green light stops flashing this is the only voltage on the psu reading low

                                Comment


                                  Re: LG 32lc46 totaly dead

                                  Originally posted by vinceroger69 View Post
                                  still nothing just rechecked voltages one says 3.4-on on the psu reads 0 volts in standby 2.00 volts when green light stops flashing this is the only voltage on the psu reading low
                                  This probably your problem check soldering for cap 2200u 10V(?)
                                  Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                  For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                  Comment


                                    Re: LG 32lc46 totaly dead

                                    remember tom66 this is not my own psu this is one i purchased so this one i am using now still got old samyoung caps in although none look bulging i will get my old unrepairable psu and swop to the panasonic ones which i put in it.

                                    Comment


                                      Re: LG 32lc46 totaly dead

                                      I have been looking at the main board - there are two switches and a large jumper
                                      - any idea what these do - does it say on the case back or inside the case back.
                                      Could not spot anything in the SM
                                      Please upload pictures using attachment function when ask for help on the repair
                                      http://www.badcaps.net/forum/showthread.php?t=39740

                                      Comment


                                        Re: LG 32lc46 totaly dead

                                        Hi Vince,

                                        I wouldnt go swapping your parts over just yet until you have properly found out what it supplying to your mainboard. If you have bought it as working then the last thing you want to do is end up with 2 power supply's in bits
                                        Fixed so far : 1 Home cinema system, 16 LCD Monitors, 4 LCD TV's

                                        How to resize your pictures guide click HERE
                                        Retiredcaps Ideal post example click HERE

                                        Comment


                                          Re: LG 32lc46 totaly dead

                                          cant see a jumper? the 2 switches no sure but bottom 1 when pressed justs seems to reset the set (starts red flashes green 5 times then nothing on screen) my old psu was no good ie only 2x5 volts present none others just swopped all caps over now just going to try it.

                                          Comment

                                          Working...
                                          X