Re: Eeprom dump thread!
Photo jointe
Photo jointe
Attached Files
-
-
Re: Eeprom dump thread!
thank you i will test it and i will let you know in the next few daysComment
-
Re: Eeprom dump thread!
Looking for eeprom for Toshiba 46SL412u
Panel LTA460HJ15
Board 461C3V51L12Comment
-
Re: Eeprom dump thread!
hello, I'm looking for the firmware for a telefunkenTE28275B31T10E, 17MB55, panel VES275wnvx-n01 led tv thanksComment
-
Re: Eeprom dump thread!
hi, I have reprogrammed the two chips U114 and U115 with the two files you posted and now it works perfectly, thanks very muchComment
-
Re: Eeprom dump thread!
hi, i am looking for the firmware for a samsung UE32D40003BV -BN41-01702A - panel LTJ320AP02-J thanksComment
-
Re: Eeprom dump thread!
hi, i am looking for the IC1604 eeprom for a Samsung UE55MU6105K -BN41-02568A / BN94-12195C - Version 02 - panel CY-GK055HGLV5H.
ThanksComment
-
Re: Eeprom dump thread!
Thanks you lotas
Here the fileComment
-
Re: Eeprom dump thread!
Do not forget about the status of the register
https://www.badcaps.net/forum/showth...=103999&page=2Comment
-
vestel 40ua9300 flash dump please
vestel 40ua9300 flash dump please
panel:ves400qnss-3d-uo1
17mb100 maın boardComment
-
Re: Eeprom dump thread!
Thank you very much lotas.
In fact I can't fully test the binaries because I don't have the TV at home, I only have the electronic boards and the LED bars.
The second binary (ue55mu6105_ic1604_II.bin) doesn't work, I don't even have the standby led.
On the other hand, the first binary (ue55mu6105_ic1604.bin) seems to work: I have the standby LED, the tv turns on with the remote control and the backlighting turns on fine. On the other hand, to test the image, I will have to wait to return to my parents and it will only be in several weeks.
I will post back to the forum at that time.Comment
-
Re: Eeprom dump thread!
Ok.Comment
-
Re: Eeprom dump thread!
Blaupunkt 32-147I-GB-5B-HBKUP-UK , tv bootloop, led red > blue > red >blue
Desolder UF11 and use CH341 for reprogram. After , go to menu and Factory reset
Firmware belowComment
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.07-26-2025, 03:24 PM -
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I...
Comment