Re: Eeprom dump thread!
Hello Lotas,
I finally took the time to copy the 2 firmwares
on the TV eeprom and everything went back in, the TV works again. I wanted to thank you a thousand times thank you...
Denis J
Member
Last Activity: 03-24-2023, 07:27 AM
Joined: 07-08-2021
Location: LIXING les SAINT AVOLD 57660
-
Re: Eeprom dump thread!
thank you i will test it and i will let you know in the next few daysLeave a comment:
-
Re: Eeprom dump thread!
The characteristics of the television
have a good day...Leave a comment:
-
Re: Eeprom dump thread!
Photo jointe...Leave a comment:
-
Re: Eeprom dump thread!
Hi there.
Techwood /chassis vestl
Card 17MB55
Panel 1405
Model TD22LED 13-3 22 inch screen
The television remains on standby, the red light on the front flashes, the Vcc 3.3v, 5v, 12v, 24v, 1.2v voltages are present. The NT72567 microcontroller heats up to 50°C.
Should I reload the flash of the U114 and U115 series or should I try the USB drive recovery software. Do you have the DUMPs, could you give them to me.
I give the U114 and U115 firwaires that I noted on the TV, can a technician tell me if they have...Leave a comment:
-
Re: Eeprom dump thread!
Hello everyone, I need a firmware and good advice. Please.
Techwood / vestel
Card 17MB55
Panel 1405
Model TD22LED 13-3 22 inch screen
The television remains on standby, the red light on the front flashes, the Vcc 3.3v, 5v, 12v, 24v, 1.2v voltages are present. The NT72567 microcontroller heats up to 50°C.
Should I reload the U114 and U115 series flash or should I try the recovery software by USB key. Do you have the DUMPs, Could you give them to me.
ThanksLeave a comment:
-
Re: Eeprom dump thread!
Hello, I need firmware and good advice. Please.
Techwood / jacket
Board 17MB55
Panel 1405
Model TD22LED 13-3
The TV remains on standby, the red light on the front flashes, the Vcc 3.3v, 5v, 12v, 24v, 1.2v voltages are present. The NT72567 microcontroller heats up to 50°C.
Advice: do I need to reload the U114 and U115 serial flash or do I have to try the recovery software by USB drive. Could you get them for me.
ThanksLeave a comment:
-
Re: Eeprom dump thread!
I extracted it from the RAR file and put on a stick formatted in fat32 put in the usb socket of the TV turned off. Then press OK on the remote control and switch on the TV.
The U10 and U12 eproms I loaded them with an EZP2019 programmer from aliexpresLeave a comment:
-
Re: Eeprom dump thread!
I also think that the problem is elsewhere although all the tensions are present and correct. I also replaced the two eprom u12 with the same reference and u10 with an EN25F32Leave a comment:
-
Re: Eeprom dump thread!
Hello lotas,
Yes all tried and the TV still does not startLeave a comment:
-
Re: Eeprom dump thread!
hello LOTAS,
I flashed the U10 and u12 eproms with the 17MB82-1A software (EN25q64; BIN ET en25q16; BIN) that you generously provided me and then I put the USB key with the vestel 17mb82-1A Recovery software USB program. When switching on the television, the LEDs of the television and of the USB key flashed quickly and at the same speed. A few minutes later the led of the USB key changed to fixed and the led of the television continued to flash more slowly and the TV still does not start. Do you have a solution for my problem.
Thank youLeave a comment:
-
Re: Eeprom dump thread!
Hello Lotas,
I'm sorry the recovery software has no action on my TV. I still have the red led flashingLeave a comment:
-
Re: Eeprom dump thread!
Thank you very much Lotas, I will test itLeave a comment:
-
Re: Eeprom dump thread!
Hello,
Can you please help me out. I am looking for firmware, dump and recovery software for a TECHWOOD TD22LED13-2 television (reference 10083420 1307) with VESTEL brand main board model 17mb82-1a, (reference 260912) for eprom U10 and U12. TV without DVD player
Thank you very much for your help.Leave a comment:
-
Re: Eeprom dump thread!
Firmware for tv techwood TD22Led 13-2 vestel chassis 17MB82-1a ref 260912. I will test this firmware
Thank youLeave a comment:
-
Re: Eeprom dump thread!
thank you very much for this quick response unfortunately the television is still on standby. Would you please have the firmware of the u10 and u12 eproms in .bin file
Thank youLeave a comment:
-
Re: Eeprom dump thread!
Good morning all,
My TV brand TECHWOOD model TD22LED 13-2 main board VESTEL 17MB82-1a (ref 260912)
stay on standby red led indicator flashes
I am looking for the FIRWARES programs of the U10 and U12 eprom can you help me please
many thanksLeave a comment:
No activity results to display
Leave a comment: