Re: LG 43UF640V half picture
my message got lost, i will rewrite next..
LG 43UF640V half picture
Collapse
X
-
Re: LG 43UF640V half picture
Faulty EEPROM maybe ? https://www.ebay.co.uk/itm/5-PCS-of-...0/253307214015Leave a comment:
-
Re: LG 43UF640V half picture
never had logo at start up,
audio is there
pins are numberedLeave a comment:
-
Re: LG 43UF640V half picture
LG logo at the boot up Is it correct? The audio of channels is present? How do you found the pins 5,6?Leave a comment:
-
-
Re: LG 43UF640V half picture
just tried resetting IC101 again pins 5 and 6, now got a screen like this ????Leave a comment:
-
Re: LG 43UF640V half picture
If you want you can buy another eeprom, equal or not equal, is enough it is a 256kbit.. and change it so the tv will reset itself.. LG also often suffer from bad cpu or bad cpu soldering, so you can try reflow it even if probably it will work for too few hours...Last edited by Davi.p; 12-16-2017, 11:47 AM.Leave a comment:
-
Re: LG 43UF640V half picture
yes still got tv channels as beforeLeave a comment:
-
Re: LG 43UF640V half picture
ok tried the eeprom reset, no change, still can not get into any settings etcLeave a comment:
-
Re: LG 43UF640V half picture
eeprom chip are always the same, 5,6 pins (sda,scl)Leave a comment:
-
Re: LG 43UF640V half picture
is it still pins 5 and 6 to resetLeave a comment:
-
Re: LG 43UF640V half picture
"2EC" is 256kbits so it's surely IC101..Leave a comment:
-
Re: LG 43UF640V half picture
IC6000 Markings
4580M
-E1
511TA3
IC101
A TMLH534
2EC L B
A3DRMA
if that helpsLeave a comment:
-
Re: LG 43UF640V half picture
If there aren't 8 pin IC's on the bottom side i ask you tell me the marking of IC6000 and IC101 (as far as i can see from a not well illuminated area)..
No Diif, that is not to touch, is the Flash eeprom for the standby software..Last edited by Davi.p; 12-16-2017, 09:17 AM.Leave a comment:
-
Re: LG 43UF640V half picture
ok got the ic with the spot of paint, not checked amy voltages on the power boardLeave a comment:
-
Re: LG 43UF640V half picture
doesn't look good. Have you verified all of the incoming pins to the main board in terms of powering / grounds to ensure that the "printed voltages" and such are there and correct... just in case you are missing some "stimuli" that is stopping the board from normal operation. What is still "funny" is that you indicated that a different tcon board allowed the picture to work "perfectly" for a little while and then you were back again to your present mode. That seems rather strange. Having said that, in my recent travels in "sharp land", a few of the subtending processing chips (signal and otherwise) get their "personality" from the eprom so if there is an issue there, then their function is totally compromised even though the set may almost work perfectly with some inputs / aspects. I suspect a 4k is even more so.Leave a comment:
-
Re: LG 43UF640V half picture
Left hand side in your photo.Last edited by diif; 12-16-2017, 09:10 AM.Leave a comment:
Related Topics
Collapse
-
Hi,
I have a VIZIO E70-E3.
Symptoms: Black screen, no picture, but LED backlights are working.
I probed the power board and voltages are as listed on the board.
Main board appears fine, too.
I believe the problem is either a bad T-CON board, or connection to LCD, or bad LCD.
There are two separate ribbon cables feeding the LCD.
If both are connected, the screen is black.
If only the ribbon cable that feeds the right side of the screen (when viewed from the front) is disconnected, the left side of the screen shows picture and... -
by shelby5041hi
i have a samsung lcd tv
it powers on with sound and backlight but no picture
all voltages from PS are good 12v 3.3v and 5v
whats odd is that at the tcon i tested voltage across the fuse on the tcon and i get 0v
i figured main board issue..so i ordered a used main board....when i put replacement main board in i still have same issue
no 12v at the tcon fuse
i disconnect the panel ribbon cables to rule out any panel issues and i still have no 12v at the tcon fuse
the odds of having 2... -
by JJAAMMThis was my main TV for the last 6 years. I'm not inclined to throw out a $2600 TV so quickly so I'm trying to investigate the issue.
Problem
TV was disconnected from power for 6 months during construction. When I plugged it yesterday picture was fine, after 30 seconds it dimmed then started developing horizontal lines, picture then starts to ghost vertically until it degrades into vertical streaks. TV always displays a perfect picture when cold. I can unplug TV for 5 minutes and plug it back in and picture is restored for 20 seconds. I can also keep it in standby mode... -
by TR103Hi, I have a Samsung UE50TU with:
- sound and backlight, but no picture
- when it arrived, it had a picture for a few seconds
- it keeps rebooting
- without ribbon cable between the two panel boards, it does not reboot but I have no picture
- without cable between mainboard and lcd panel, it does not reboot (but obviously i have no picture)
- when i try a tape fix, its keeps rebooting, unless I tape off pin 1 (the innermost pin). In that case it does not reboot but I have no picture.
- without cable between mainboard and lcd panel and with a jumpered... -
by Daren87Hello everyone,
I've recently been given a Sony 8k Z8H. It's got a white screen with two vertical black bars. At times it's given me the 5 blink Tcon code. Testing voltage on the Tcon I can see some low or missing voltage. I've done a basic visual check of cables and the COF. Not seeing anything obvious. The original Tcon seemed to have good caps until turning it over. On the bottom I found maybe 10 caps with both sides of the caps shorting to ground. I thought ok these caps and likely other components on the Tcon are shorted so let's try a replacement Tcon. I just received the... - Loading...
- No more items.
Leave a comment: