Philips 37PFL8605 help

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • focus6666
    New Member
    • Jun 2017
    • 3
    • Bosnia

    #1

    Philips 37PFL8605 help

    Hi friends

    I recently bought Philips 37PFL8605 , but I have problems with picture.
    When I turn on TV I have vertical strips in middle of screen, and T-Con is overheating , these two ICs on Tcon get very hot.



    Also my power supply gets hot, only on transformer marked as 2NP000080DA-R.

    I want to order new boards, but I can not diagnose fault, is it bad T-Con ,or power supply or lcd panel.

    Can you please help me with diagnose.

    Thank you
  • attainteddragon
    Badcaps Veteran
    • Apr 2013
    • 764
    • australia

    #2
    Re: Philips 37PFL8605 help

    post a picture of the screen problem.

    advanced, manage attachments, then upload the pic.

    from there it will appear as a thumb tile that we can blow up if we need to.

    add a pic of the entire rear of the tv too thanks.
    WHY CAN'T PHILIPS USE PHILLIPS HEAD SCREWS?

    Comment

    • focus6666
      New Member
      • Jun 2017
      • 3
      • Bosnia

      #3
      Re: Philips 37PFL8605 help









      Here you can see vertical lines I have on display.
      Attached Files

      Comment

      • dskall
        Badcaps Legend
        • Oct 2016
        • 2905
        • usa

        #4
        Re: Philips 37PFL8605 help

        I would say bad panel. Possibly something shorted on panel pcb
        I assume no responsibility for any stupid suggestions I might post.

        Comment

        • attainteddragon
          Badcaps Veteran
          • Apr 2013
          • 764
          • australia

          #5
          Re: Philips 37PFL8605 help

          if you slightly flex the panel, (bottom edge in this case), does the picture change at all?


          and is the fault over the menu screen?
          WHY CAN'T PHILIPS USE PHILLIPS HEAD SCREWS?

          Comment

          • budm
            Badcaps Legend
            • Feb 2010
            • 40746
            • USA

            #6
            Re: Philips 37PFL8605 help

            One of those tab bonding board on the bottom edge of the panel which gets damage by the cleaning fluid, so look for corrosion on that area of the tab bonding board.
            Never stop learning
            Basic LCD TV and Monitor troubleshooting guides.
            http://www.badcaps.net/forum/showthr...956#post305956

            Voltage Regulator (LDO) testing:
            http://www.badcaps.net/forum/showthr...999#post300999

            Inverter testing using old CFL:
            http://www.badcaps.net/forum/showthr...er+testing+cfl

            Tear down pictures : Hit the ">" Show Albums and stories" on the left side
            http://s807.photobucket.com/user/budm/library/

            TV Factory reset codes listing:
            http://www.badcaps.net/forum/showthread.php?t=24809

            Comment

            Related Topics

            Collapse

            • Daren87
              Sony 8K XBR-75Z8H White Screen Vertical Bars Tcon Code. Help Needed🙏
              by Daren87
              Hello everyone,

              I've recently been given a Sony 8k Z8H. It's got a white screen with two vertical black bars. At times it's given me the 5 blink Tcon code. Testing voltage on the Tcon I can see some low or missing voltage. I've done a basic visual check of cables and the COF. Not seeing anything obvious. The original Tcon seemed to have good caps until turning it over. On the bottom I found maybe 10 caps with both sides of the caps shorting to ground. I thought ok these caps and likely other components on the Tcon are shorted so let's try a replacement Tcon. I just received the...
              08-13-2023, 03:25 PM
            • advant
              Driving a Sharp TCON/panel with a universal main board
              by advant
              This thread is about trying to get an Universal Main Board to work with a Sharp TCON and panel.

              I have a Sharp LC-46D85UN TV that has had a main board issue. Since this model is from 2009, I am not able to find an exact replacement of the main board. Instead, I decided to see if I can future proof this tv by getting a Universal Main Board (T53U21.2) from China to work with the Sharp TCON (CPWBX4291TPZA) and panel. The universal main board supports a 8 bit dual channel LVDS interface whereas the TCON requires a 10 bit dual channel LVDS input. I have modded the LVDS connector to match...
              02-03-2020, 12:25 AM
            • tehmatix
              Pc monitor Philips 279M1 - red vertical stripe
              by tehmatix
              Hi,
              I got this monitor Philips 279M1 and the issue is : when is cold (turn off for few hours, not in standby) and turn it on it's coming whit a red vertical stripe. After 5 minutes or less (depend on the room temperature) the stripe disappearing
              A short video
              https://youtu.be/gj5vKF_xBMU...
              06-09-2023, 09:42 AM
            • kca
              LG 82UN8570AUD ~ TCON or PANEL?
              by kca
              Hello all ~

              Hope this finds you well. This LG 82UN8570AUD (April 2021 model) 4K UHD television has full audio capabilities but video is compromised / problematic.

              When I picked up this large LG tv it had a full black screen upon startup. Previous owner said it just went black one day. No popping sound or anything else of note.

              I got the display to work by taping off several traces of the right-hand side ribbon cable on the TCON that leads from TCON to PANEL. However, despite dozens and dozens of attempts to find the right combination / range of traces taped...
              08-31-2025, 06:38 AM
            • x_orange90_x
              TCL 50S535 bad tcon or panel issue?
              by x_orange90_x
              Just bought this for 10 bucks yesterday hoping to fix it. The guy said water dropped inside from a dehumidifier hose and it started showing black and white vertical bars then went blank. When I got it home and turned it on it came on fine and displayed correctly but I was noticing faint vertical bars in the image. After a little bit I turned it off and back on and it was a black screen again. I opened it up to check for water damage and corrosion but didn't find anything of the sort. I cleaned the ribbons anyway and reconnected them but still got a blank screen. If I disconnect the right side...
              03-29-2025, 11:02 PM
            • Loading...
            • No more items.
            Working...