I’ve checked everything I can think of and have run out of ideas. It will not turn on and there is no stand by light. I have been looking for some schematic drawings with no luck. Thanks any help will be appreciated.
-
My Spelling and Grammer Sucks.
-
Re: Proscan LED 32" TV not working.
We need good clear sraight on pictures of back of tv with cover off and one of each board.
We also need the voltages from the power supply connectors.
Format:
Pin Label - Pin Voltage standby - Pin voltage power on
1 - XXXXXXX - XXv - XXXv
2 - XXXXXXX - XXXv - XXXv
3 - XXXXXXX - XXXv - XXXv
4 - etc.
Please remember we dont have the tv in front of us so we go from the information you provide us ie pictures voltage readings etc. -
Re: Proscan LED 32" TV not working.
So far all I could check was the Power board. Starting at the top and each pin grounded to its own plug gnd pin. each plug's measured voltage is separated with a semi-colon.
25.65, 25.65, 25.65, and 25.65 VDC : 25.67, 25.7 : 13.62, 13.62, 5.04, 5.04, 5.04, 5.04, 0, and 0 VDCAttached FilesMy Spelling and Grammer Sucks.Comment
-
-
Re: Proscan LED 32" TV not working.
I played with paint to see if this would help.Attached FilesMy Spelling and Grammer Sucks.Comment
-
-
Re: Proscan LED 32" TV not working.
theres two pins marked plus 5v so your getting no voltage to them as it looks like it uses the same pcb trace as the working two plus 5v pins or are they not used on the top side of the board
can you upload a picture showing the whole back of the tv and how all the boards are connectedLast edited by vinceroger69; 05-22-2017, 05:50 AM.Comment
-
Re: Proscan LED 32" TV not working.
I separated the wires (i.e. the 5VDC).My finger is on one and my tweaker is pointed at the other end. The color bars are medium blue line and wire with no bands.Attached FilesMy Spelling and Grammer Sucks.Comment
-
-
Re: Proscan LED 32" TV not working.
Does anyone have an Electrical schematic?
My Spelling and Grammer Sucks.Comment
-
Re: Proscan LED 32" TV not working.
To make it easier for us to figure what Voltage and Control signals are present, please look at the bottom side of the board and list the pin names of each connector and follow by the the DCV readings for each pin after the power switch is activated.
http://www.shopjimmy.com/catalogsear...t/?q=PLED3216a
http://www.shopjimmy.com/proscan-ay0...upply-unit.htm
Pictures provided by shopjimmy.Attached FilesNever stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
-
Re: Proscan LED 32" TV not working.
I thought I did. the only pins I didn't get VDC on was the bottom pins ie the 2 5vcd pins. Zoom in. Maybe?Attached FilesMy Spelling and Grammer Sucks.Comment
-
-
Re: Proscan LED 32" TV not working.
thats good it looks like the psu is ok too me do you get any sound on the tv? maybe try a dvd player etc through a scart socket roughly at the centre of the tv theres two metal covers covering two boards tcon and led driver board naybe can you remove the covers and take pictures of these two boardsComment
-
Re: Proscan LED 32" TV not working.
It looks like the power supply board does not have the connector installed where the ON/OFF, ADJ pins are located for controlling the backlights circuits.
You do have PS-ON command signals so the main board is not completely dead that is why you are getting the switched 5V, 12V, and 24V.
The small board in the middle is the LED driver board, I can see two wire going to the main board which I believe those two wire contain the Backlights ON/OFF control signal and the Dimming control signal.
So check to see if the PS-ON pin does change state or not when you turn the TV ON and OFF.
Then probe those two wires on the LED driver board to see what DCV you have when turning the TV ON and OFF.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Proscan LED 32" TV not working.
PS-ON does not change. It stays high at 5VDC.
Ill get you the other info as soon as I can.My Spelling and Grammer Sucks.Comment
-
Re: Proscan LED 32" TV not working.
Here is the other pics. Let me know if your guys need anything else.Attached FilesMy Spelling and Grammer Sucks.Comment
-
-
Re: Proscan LED 32" TV not working.
on your second picture theres a fuse marked f1 if you dont want too put all the tv boards back in place and measure the voltage to each side of the fuse you could measure the ohms reading straight across the fuse just to check its not openComment
-
Re: Proscan LED 32" TV not working.
I was thinking that my stand by was in the center of my power button. I was mistaken. I found this a little while ago.Attached FilesMy Spelling and Grammer Sucks.Comment
-
-
Re: Proscan LED 32" TV not working.
yes thats the standby led board and remote sensor etc so the standby button led does work it looks like red in standy blue when onComment
-
Re: Proscan LED 32" TV not working.
I believe its green when on. so.... Power supply looks good. what else do I need to check. I Work 11pm to 7am. CDT. Ill get back with you guys after my shift starts.My Spelling and Grammer Sucks.Comment
-
Re: Proscan LED 32" TV not working.
sorry it is green i zoomed in on the pcb in your picture and now have seen the print g and r i would check you get voltage too both sides of fuse marked f1 im not sure why ps on voltage dosnt change so maybe a mainboard fault? im sure budm will advise usComment
-
Re: Proscan LED 32" TV not working.
At this point you have main board problem, that PS-ON should never stay in one level, it should change state when power switch is toggled.
I see 3-pin Voltage regulator ICs on the main that you should check the Voltages, see the link on how to test and how to report the readings properly.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Hello,
i have many 5050sff. all of them, and how i experienced over many years for all about 250 DELLs goin through my hands, are fully flashable and can be serviced in any way when the service_mode jumper is set.
Never ever i experienced problems with that.
Now i have one 5050sff machine, where this jumper isnt working at all.
I do not get the normal messge that the jumper is set when booting and a short test with FPT just confirms this. Everything is locked -->> EVEN for reading !?
The history of the machine is that i used it in my office... -
Hi,
I have the above mentioned bord after repair, which was related to a lot of missing smd devices on the back of the board.
There were almost 20 devices missing, caps, resistors and some diodes/mosfets.
The board is generally working now, all PCIe ports are working, Windows installs normally.
However I have a problem with SATA ports 4-7 (the board has 8 SATA ports) - disks are not beeing recognized by the BIOS neither by Windows (which is usually normal in case BIOS does not recognize them).
The SATA 4-7 driver network is quite simple chipset<->buffers/drivers<->SATA... -
Hi i have one Macbook Air 2020 where touch ID is not working (it's not scanning fingerprints). Touch ID was working before, there is no error message during scanning fingerprint it's just not scanning on screen you can see only fingerprint but there are no red updates as when it's working. Power button is working fine.
I've checked boardview and also schematics but i'm not able to find anything related to TouchID ... i have similar issue on a2338 where there was problem with PP3V0_TOUCHID and after replacing UT610 it was working but here i'm not able to find anything related to... -
Hi masters, I need your help.
I am working on Lenovo Legion 16ITHg6
Motherboard number NM-D721, no BV, no schematic but I am attaching very closes ones.
INPORTANT: My motherboard version is with IT8258 IC, that is controlling keyboard and RGB LEDs.
My problem is on UI142, +3VALW_AG is not stable, floating from 0V to 3,3V.
AGKB_PWR_EN_N signal is floating too (that is why+3VALW_AG not stable).
Power LED is not working as well, power button working well.
UI26 ??? is there any firmware too? Powered by +3VALW_AG.
Motherboard...05-04-2025, 09:35 AM -
Hi there,
It is sunday and I got a faulty hp pavilion 15-cs1006na. No available schematics on the entire world. It flashed 5 long 4 short and no post then I discovered the usb 2.0 2. pin in one of the usb-a socket bent backwards and been shorted to 2. and 3. pin of the 3.0. after removing this short in the port the laptop came alive.
Now the laptop freezing randomly. The webcam, the built in mic and according to the device manager one more thing not working which are connected to usb. If I connect anything what have usb 2.0 plug that wont work if i plug anything what...
Comment