Re: Eeprom dump thread!
main 17MB211S and VES315WNDS-2D-N21
Plese
Te Rog
main 17MB211S and VES315WNDS-2D-N21
Plese
Te Rog
-
-
Re: Eeprom dump thread!
Philips 65PFL8708S/12 - Chassis QFU1.2E LA
Current main software: QF2EU-0.173.67.0_bld5a
Standby software: STDBY_77.4.8.16
Attached working dumps:
7CT3 M25P10-AV@SOIC8: SPI Flash with Standby Processor software and NVM
7JA2 M24C64-W@TSSOP8: I2C EEPROM with NVM
7HA0 Sil9287BCNU: EDID-data
Note; EDID can only be read through HDMI, if you try to write EDID through HDMI it will not persist in the memory.
You have to hook into the I2C-pins to successfully write the EDID.
I have the NAND too, but it's too big to post here.Last edited by Maalobs; 01-23-2024, 05:45 PM.Comment
-
Re: Eeprom dump thread!
Have to say this thread was totally useless to me, for others that also find it useless (probably quite a lot of u) you will just need to bite the bullet and buy a new motherboardComment
-
Re: Eeprom dump thread!
good day for all I need to see who does me the favor of passing me the dump for a tv apex model LE4643T with panel number V460HJ1-PE1. thank you and blessings for allComment
-
Re: Eeprom dump thread!
HELLO FRIENDS I need dell moniter model no. SE2216H DUMPComment
-
Re: Eeprom dump thread!
Hello All,
Do you have a
dump for a COBY TFTV4028
Main Board---002-FV40-2812-00R
Panel---T400HW03 V.2
ThanksComment
-
Re: Eeprom dump thread!
Hi All,
Does anyone have a dump for a vizio?
Model E390-A1
mainboard----715G5560-M01-000-004K----TXCCB02K042
PANEL---TPT390J1-HVN01 REV:000A
ThanksComment
-
Re: Eeprom dump thread!
Hi everyone. I am searching for a working dump for a Finlux 32flhyr274 tv, with vestel ves315wnda-2d-n11 screen, 17MB82S MB and 17IPS62 power supply.
I tryied at least 10 dumps but if it starts, and the image isn't rotated the image quality is bad, and the remote isn't working very well.
other codes are also at each sticker,
backplate: 10106321 1611 601841
sn: 7694659 601841
screen: ves315wnda-2d-n11
23335377
VEL_LCM VES315WNDA2DN11_15_32261WCLWOR&S
tuner: 10106321 23335403 2186 32"
27696409 DIJ
1129
23239021 96409
V1129 LN4 ST
05*11 - 20/8-141
Hope somebody can help me with the good working dumpsComment
-
Re: Eeprom dump thread!
Good afternoon,
I hope i write in correct section.
My blaupunkt tv turn on but no image on the sreen
So i think i can be a firmware bug!
i'm wondering if it exists a way to re upload the firmware using usb port by using a specif key press in tv buttons or using remote control ?
Many thanks to anyone that can explain me how to do if it is possible.
When it's not possible to make any add-on (cable, connector, etc.) that makes it possible to upload frimware. I think the new product are also somehow upload at the factory.
Firmware for this TV:
main board is t.msd309.btu87 (4k tv)
and panel display innolux V400DK1
I attached some picture about my tv.
Thank you for your help.Attached FilesComment
-
-
Re: Eeprom dump thread!
Hi everyone.
I am searching working dump spi flash for led tv 32".
main: LD.M3393.E
add unit: LF.M30.A1 1305
FHD panel: LTA320HJ03
Thanks in any caseComment
-
Re: Eeprom dump thread!
Hi everyone.
I am searching working dump spi flash 25Q32.
TV: MEDION
model: MD30479 DE-W
main: T.MSD309.8B 10304
panel: LTI320AP01
Thank you!Comment
-
Re: Eeprom dump thread!
Salve TV Diunamai wd-tv6600
Main board : T.sp7050.9b 9502
Power : ipb322s2
pannello P190MWW3
tuner CDT-SFT338-40
U11 =25L80
U9 =24c02
U10 =24c02Comment
-
Sharp LC-32CHG6201K
Sharp LC-32CHG6201K
Blue screen, no pic & menue, will not turn off.
Format usb stick FAT32, copy files.
Unplug TV, insert USB stick & power up. Update progress appears on screen and takes about 7 mins.
When complete, the set switches OFF - WAIT 1 or 2mins. until LED flashes rapidly then unplug and remove usb stick, power back ON.
The instructions said to wait 15-20mins (this should read 15-20seconds I reckon), it takes 15-20 seconds to 'boot' the TV. I had it in 'Burn-in mode' and simply had to unplug, press the 'wobble button' at the back while plugging back in. I now had a working TV.
Note This set is made by Hisense a UMC clone.Comment
-
Re: Eeprom dump thread!
as a member of this top notch site which over the years has helped me out alot. i want to give back.. so ive uplloaded a shed load of files to one of my servers enjoy,! and if you require any new JVC tv firmware. i have lots more, please ask,. what software / firmware or files you are after you never know as a tech i might have it cheers ..
PLEASE SAY THANKS,
http://77.81.110.132/Firmware/As36dFeRcVgFdd7g23JkLbX/
DONT MISSTREAT MY SERVER PLEASE.Comment
-
Re: Eeprom dump thread!
Thank youComment
It is appreciated as they can be hard to get hold of especially the more obscure TV brands like Logik etc.
-
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... -
Comment