Vestel 17mb110p
In need of dump.
Panel VES430UNDL-2D-N12.
Thank you
In need of dump.
Panel VES430UNDL-2D-N12.
Thank you
-
-
-
Re: Eeprom dump thread!
Thank you. What about the dump from SPI MX25L1606E (2MB)?Comment
-
Re: Eeprom dump thread!
Thank you again.Comment
-
Re: Eeprom dump thread!
Here is a firmware from a 40" RCA LED TV:
Model: RLED4010A (Canada)
EEPROM Chip type: Winbond 25Q32
Panel type: Samsung
I don't know the mainboard model, as the EEPROM was read a long time ago before I found this thread.Comment
-
Re: Eeprom dump thread!
Here is a firmware from a 32" RCA LED TV:
Model: RLDED3260A (Canada)
EEPROM Chip type: Original chip was MX25L1606E, successfully reprogrammed to 25Q16BSIG
I don't know the mainboard model, as the EEPROM was read a long time ago before I found this thread.Last edited by Unspun01; 12-10-2018, 07:04 PM.Comment
-
Re: Eeprom dump thread!
Here is a firmware from a 32" RCA LED TV:
Model: RLDED3258A (Canada)
EEPROM Chip type: 25Q16BSIGComment
-
Re: Eeprom dump thread!
Can anyone upload a firmware for an RCA 32" LED TV?
Model: RLED3216A (Canada)
Mainboard: CV318H-X
EEPROM type: Winbond 25Q16CVSIG
EEPROM Location: U10
Panel: AU T315XW06 V.6
May be same or similar to Proscan PLED3216AAttached FilesComment
-
-
Re: Eeprom dump thread!
Can anyone out there help me find some Epprom software for a bush 22 led tv with a 17mb82-2 main board, I’ve tried other firmware for that board but it doesnt seem to be able to talk to the led panel, the led panel number is :m215htn01.1 , any wizards out there with firmware compatible, or maybe another one, I can get the tv to boot if I freeze the chips maybe from there someone can guide me to updating the firmware?Comment
-
Re: Eeprom dump thread!
Tv led vortex v24e16df
panel auo m240htn01.0
chassis t.emr380.61
i need bin file 25q64 or usb firmware update
many thanks ?????Comment
-
Re: Eeprom dump thread!
Hi I need software
HKC-H32PB1000
Main : CV59TH-A32
Panel :
HV320WX2-506
Thanks in advanceComment
-
-
Re: Eeprom dump thread!
Firmware for WT61P805 Samsung TV
UN32EH5300F
UN46EH5300F
UN50EH5300F
UN55EH5300F
UN46ES6100F
UN50ES6100F
UN55ES6100F
and other
Main Boards:
BN94-059175
BN97-06298N
BN94-05750K
BN97-06430LAttached FilesComment
-
-
Re: Eeprom dump thread!
Morning
Can you check for a boot file for a Telefunken 32" LED TV Model TLEDD-32HD Require Firmware
DankieComment
-
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... -
Comment