Jvc em42ftr doesn't turn on.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • crdz66
    Badcaps Veteran
    • Nov 2012
    • 242
    • USA

    #1

    Jvc em42ftr doesn't turn on.

    Hello fellas.

    I have a led jvc tv model em42ftr that doesn't turn on
    i get this tv from a customer that said after thunder day(heavy rain) in her house the tv don't want turn on.

    The first thing i did it was to check the fuse and i find a short (no continuity).
    I replace the fuse and as soon i plug the power cord the fuse blow again.
    I decide to replace the power supply board and still can make turn on the tv.
    I check the voltage going to the main board.

    1. 19v - 19v
    2. 19v - 19v
    3. 19v - 19v
    4. Gnd
    5. Gnd
    6. Gnd
    7. Ps_on - 0v
    8. Bl_on - 0v
    9. Dim1 - .06v
    10. Dim2 - .06v

    there is a 6 pins connector on main board.

    1. -
    2. -
    3. 3.2v
    4. Gnd
    5. 5.1v
    6. 1.6v

    power on button on remote or tv doesn't make turn on.

    Any idea can be appreciate.
    Thanks.
  • budm
    Badcaps Legend
    • Feb 2010
    • 40746
    • USA

    #2
    Re: Jvc em42ftr doesn't turn on.

    The main board is not sending the PS-ON signal to turn on the rest of the power supply, same for the BL-ON, and the dimming signals, all dead.
    Never stop learning
    Basic LCD TV and Monitor troubleshooting guides.
    http://www.badcaps.net/forum/showthr...956#post305956

    Voltage Regulator (LDO) testing:
    http://www.badcaps.net/forum/showthr...999#post300999

    Inverter testing using old CFL:
    http://www.badcaps.net/forum/showthr...er+testing+cfl

    Tear down pictures : Hit the ">" Show Albums and stories" on the left side
    http://s807.photobucket.com/user/budm/library/

    TV Factory reset codes listing:
    http://www.badcaps.net/forum/showthread.php?t=24809

    Comment

    • crdz66
      Badcaps Veteran
      • Nov 2012
      • 242
      • USA

      #3
      Re: Jvc em42ftr doesn't turn on.

      Even I not get Red light indicator at the front

      Comment

      • crdz66
        Badcaps Veteran
        • Nov 2012
        • 242
        • USA

        #4
        Re: Jvc em42ftr doesn't turn on.

        After replace the main board this tv is working good.
        Now I get 3.2v on p_on connector.

        Thanks Fellas

        Comment

        Related Topics

        Collapse

        • corrize
          A funny fuse story – Lumix LX100 II
          by corrize
          Hello, I disassembled this dead camera, and found this WTF… Two fuses soldered one above the other !
          I was pretty sure nobody touched it before, but that can't be from factory. There is flux, and capacitor is probably missing.
          The other weird thing : the fuses are « G » fuse : (0.75A – 8V), seems very low. The original fuse should be « O » : (32V 2,5A).
          There is « O » mark beside. All fuses have the same mark letter on main board. So, I can deduce it's a « O » fuse.
          And this correspond to the issus I saw : when I plug the battery, I measure the voltage dropping...
          10-19-2023, 09:58 AM
        • pajdek
          Lenovo Y700-17ISK turn on and off
          by pajdek
          Hello, i have some issues with my laptop Lenovo Y700-17ISK (motherboard BY511 NM-A541), it started when i turn on the laptop, but the lcd wont turn on, i then connected it via hdmi to tv and screen was ok. So i thought maybe lcd stripe is faulty, i removed the bottom cover, disconnected main battery, reset the cmos by disconnecting battery for 1 min, then slighty move the lcd stripe. Conncted power supply and tuned on my laptop, the lcd turn on, it started to load os, then it turn off, after a second it turn on, then after like 3 seconds turn off again, and so on. Removed power supply, waited...
          09-20-2023, 02:49 AM
        • Document Archive
          Surface Mount Fuses Fundamentals Datasheet
          by Document Archive
          TE Circuit Protection offers the widest selection of surface-mount fuses available for addressing a broad range of overcurrent protection applications. Helping to prevent costly damage and promote a safe environment for electronic and electrical equipment, our single-use chip fuses provide performance stability to support applications with current ratings from .5A up to 20A.

          TE Circuit Protection also offers the telecom FT600 fuse for telecommunications applications. This telecom fuse helps comply with North American overcurrent protection requirements, including Telcordia, GR-1089,...
          10-07-2024, 06:07 AM
        • RdeveLabs
          MSI GF63 THIN 11UCX (MS-16R6) LAPTOP WON'T TURN ON AFTER RESTARTING
          by RdeveLabs
          To all the members here...

          Let me tell you a little bit about what happened to my laptop (MSI GF63 THIN 11UCX model: MS-16R6) that “maybe” you know how to solve this problem.

          So before this problem happened, my laptop was running smoothly. When I wanted to restart my laptop, it looked fine at first. But after I waited for this restart process to take a long time, until finally I panicked (because the restart process did not finish plus the laptop screen only showed a black screen), I immediately pressed and held the power button to force the laptop to turn off. But...
          05-05-2025, 04:59 AM
        • robante15
          Acer Aspire 4520 won't turn on after reboot
          by robante15
          Hello, I have an Acer Aspire 4520 from a couple of decades ago and I want to repair it solely for nostalgia.

          It happens that when I turn it on after having been disconnected for a long time, it turns on without problems, it tells me that the BIOS has been reset and that it will load the factory settings, if I tell it to continue, the computer turns on and everything works fine.

          The moment I turn it off and want to turn it back on a second time, or restart it and try to start it again, it no longer gives an image, and it no longer responds.

          If I remove the...
          04-06-2024, 06:50 PM
        • Loading...
        • No more items.
        Working...