VIORE 32" - Power board problem?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sansonet
    Badcaps Veteran
    • Nov 2013
    • 236
    • US

    #1

    VIORE 32" - Power board problem?

    At least I think it is power board. But I could be wrong. TV - VIORE LC32VH56, symptoms - upon plugging in, green power light comes on and stays on, no blinks, etc. But nothing else. I can't even turn it off, pressing power button doesn't do anything. I have component tester so I unsoldered and tested all caps. They little lower than specs, but withing 20% limit, most not lower than 10%. Tried 24V light bulbs in 24V output - nothing. Multimeter doesn't show any power too. I'm attaching pics of power board and main board. Is there anything else I can test to find a problem?
    If nothing else, I could buy used power board to replace it, they are not very expensive, but I want to be sure that will fix a problem before I'll spend money on it.
    Attached Files
  • newtothis
    Badcaps Legend
    • Mar 2013
    • 1556
    • england

    #2
    Re: VIORE 32" - Power board problem?

    Read 5v at any of the pins from the connector that goes from PSU to main?

    Comment

    • sansonet
      Badcaps Veteran
      • Nov 2013
      • 236
      • US

      #3
      Re: VIORE 32" - Power board problem?

      In reference to first picture, main board connector (CON4) from left to right:
      1. GND
      2. GND
      3. 0.32V
      4. 0.32V
      5. PS-ON -2.75V
      6. +5VSB - 5.16V
      7. 0.32V
      8. 0.32V

      no reading on rest

      Comment

      • newtothis
        Badcaps Legend
        • Mar 2013
        • 1556
        • england

        #4
        Re: VIORE 32" - Power board problem?

        Do you have a resistor between 470ohms and 1K?

        Comment

        • sansonet
          Badcaps Veteran
          • Nov 2013
          • 236
          • US

          #5
          Re: VIORE 32" - Power board problem?

          Originally posted by newtothis
          Do you have a resistor between 470ohms and 1K?
          To replace it on power board? You think it got bad one? I have component tester and can test it if I know which one to test. If it need to be replaced, I can try to find one. I have some old boards and I can see if it got resistor like this, or I can buy one.

          Comment

          • newtothis
            Badcaps Legend
            • Mar 2013
            • 1556
            • england

            #6
            Re: VIORE 32" - Power board problem?

            No, its so we can jump the PS-On and 5v Standby pins on the PSU to see if its the main board at fault. An old one of a board will work as long as its between those specs

            Comment

            • sansonet
              Badcaps Veteran
              • Nov 2013
              • 236
              • US

              #7
              Re: VIORE 32" - Power board problem?

              OK, I'll try to find one tonight. If I do, what I should do with it and how can I detect if board is at fault?

              Comment

              • newtothis
                Badcaps Legend
                • Mar 2013
                • 1556
                • england

                #8
                Re: VIORE 32" - Power board problem?

                Well would guide you if you found one that is ok to use... What we would be hoping for is for the backlights to come on.

                unplug the TV

                Would need to disconnect the PS_ON cable from the mainboard (so using a pin can remove it from its connector or cut the cable - just make sure there is enough cable to connect it back up) Leave the rest of the connections in place.

                Jump PS_ON to the +5VSB using a resistor between 470ohms and 1Kohm

                Plug set in.

                i have a feeling the Main is at fault and is holding the PS_ON signal wrong.

                Comment

                • sansonet
                  Badcaps Veteran
                  • Nov 2013
                  • 236
                  • US

                  #9
                  Re: VIORE 32" - Power board problem?

                  Ok, I can't do this now, but I'll try to find this resistor tonight and I will get back here when I do.

                  Comment

                  • budm
                    Badcaps Legend
                    • Feb 2010
                    • 40746
                    • USA

                    #10
                    Re: VIORE 32" - Power board problem?

                    "5. PS-ON -2.75V" Main board is supplying 2.75V which is enough for the Power supply to come on. So you need to troubleshoot the power supply board.
                    BTW, there are no label on the pins for the BL_ON and DIM signals?
                    Whole pictures of the top side and the bottom side of this power supply board?
                    Last edited by budm; 12-18-2013, 01:19 PM.
                    Never stop learning
                    Basic LCD TV and Monitor troubleshooting guides.
                    http://www.badcaps.net/forum/showthr...956#post305956

                    Voltage Regulator (LDO) testing:
                    http://www.badcaps.net/forum/showthr...999#post300999

                    Inverter testing using old CFL:
                    http://www.badcaps.net/forum/showthr...er+testing+cfl

                    Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                    http://s807.photobucket.com/user/budm/library/

                    TV Factory reset codes listing:
                    http://www.badcaps.net/forum/showthread.php?t=24809

                    Comment

                    • tibimakai
                      Badcaps Legend
                      • Jan 2012
                      • 3680
                      • USA

                      #11
                      Re: VIORE 32" - Power board problem?

                      I have worked on only one 32" LED Viore TV, but my experience with it, it was bad solder joint(s).
                      Worth checking the solder joints. Worst soldering job, that I have ever seen. It was done manually, by some beginner!!!

                      Comment

                      • sansonet
                        Badcaps Veteran
                        • Nov 2013
                        • 236
                        • US

                        #12
                        Re: VIORE 32" - Power board problem?

                        OK, I found this one - it shows about 810 ohm in tester. Should I use it?
                        Attached Files

                        Comment

                        • sansonet
                          Badcaps Veteran
                          • Nov 2013
                          • 236
                          • US

                          #13
                          Re: VIORE 32" - Power board problem?

                          I just tried it, not sure if I jumped it correctly, but TV acted without changes, still just green light on and nothing else.
                          Attached Files

                          Comment

                          • sansonet
                            Badcaps Veteran
                            • Nov 2013
                            • 236
                            • US

                            #14
                            Re: VIORE 32" - Power board problem?

                            Originally posted by budm
                            BTW, there are no label on the pins for the BL_ON and DIM signals?
                            Whole pictures of the top side and the bottom side of this power supply board?
                            No, I don't see such labels anywhere on the board. Here are top/bottom pictures
                            Attached Files

                            Comment

                            • philliesfan30m
                              Badcaps Veteran
                              • Aug 2013
                              • 542
                              • USA

                              #15
                              Re: VIORE 32" - Power board problem?

                              did you check d2 and the other 1 by j10 on the heatsink they both look burnt or bad solder joints compared to the other 1

                              Comment

                              • sansonet
                                Badcaps Veteran
                                • Nov 2013
                                • 236
                                • US

                                #16
                                Re: VIORE 32" - Power board problem?

                                Yes, they connected, I checked with continuity tester and with component tester. They don't look as good and have left over solder paste because I messed it up a little when I removed heatsink to get to caps. There row of 6 cups right under heatsink and it's is hard to get them out without removing it first.
                                Last edited by sansonet; 12-18-2013, 10:26 PM.

                                Comment

                                • philliesfan30m
                                  Badcaps Veteran
                                  • Aug 2013
                                  • 542
                                  • USA

                                  #17
                                  Re: VIORE 32" - Power board problem?

                                  was this your tv or did someone else mess with it at all? and that 47uf50v cap on our mainboard is that just rust or some crap on the back of the cap or did it explode? so when you plug the tv in it tries to power right up? it doesn't go into standby mode and when you push the power button it doesn't do anything?

                                  Comment

                                  • sansonet
                                    Badcaps Veteran
                                    • Nov 2013
                                    • 236
                                    • US

                                    #18
                                    Re: VIORE 32" - Power board problem?

                                    Caps on mainboard are OK from what they look like, but I didn't test any of them. That 47uF cap is OK too, it just got some of that red adhesive they used around screws. I don't think somebody else "messed" with it, it was given to me because it doesn't work so they gave it away. TV not "tries" anything at all, only green led comes on and stays on. No reaction on power button or any other, it have to be unplugged to turn it off.

                                    Comment

                                    • philliesfan30m
                                      Badcaps Veteran
                                      • Aug 2013
                                      • 542
                                      • USA

                                      #19
                                      Re: VIORE 32" - Power board problem?

                                      what about the wiring going to the power button on the front of the tv? did you look at that? and where does that connect on the power board? it should go into standby not right on which is the green light it should be red first i believe

                                      Comment

                                      • philliesfan30m
                                        Badcaps Veteran
                                        • Aug 2013
                                        • 542
                                        • USA

                                        #20
                                        Re: VIORE 32" - Power board problem?

                                        even so it still isn't turning on and showing a backlight and picture. does it have sound or no? did you check just the caps or did you check the diodes and mosfets?

                                        Comment

                                        Related Topics

                                        Collapse

                                        • Tynan Dill
                                          Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                                          by Tynan Dill
                                          I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                                          Upon bringing it home and plugging it up, it showed a standby light.

                                          I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                                          The screen seems to blackout and stay black, but with a flashlight I can see the display.

                                          With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                                          Assuming...
                                          11-22-2024, 01:46 PM
                                        • Destroyer-Br
                                          [HELP] Acer AN515-55 (LA-J871P Rev: 1B) – Board won't power on after GPU investigation – Suspecting Super I/O or PCH
                                          by Destroyer-Br
                                          [HELP] Acer AN515-55 (LA-J871P Rev: 1B) – Board won't power on after GPU investigation – Suspecting Super I/O or PCH

                                          Hi everyone,

                                          I'm working on an Acer Nitro 5 unit with the following specs:
                                          • Motherboard: LA-J871P Rev: 1B
                                          • Model: Acer AN515-55-59MT
                                          • S/N: NHQ7JAL00403906A973400
                                          • SNID: 03902728734

                                          Initial Issue


                                          The laptop initially presented graphic issues and driver failure (Code 43) for the GPU.

                                          After preventive maintenance (cleaning, thermal paste, etc.), it powered on normally. We disassembled it again to inspect the GPU, reassembled...
                                          04-17-2025, 08:18 PM
                                        • Dani_2024
                                          Sceptre U550CV-UMR 4K LED, Bad Caps on Main Power Board?
                                          by Dani_2024
                                          Hi and thanks in advance for any input you might provide!
                                          I have a Sceptre U550CV-UMRD8POTV83BB 4K LED (this is a dumb tv) that I bought new in August 2021, so It's just completed 3 years.
                                          Main power board model: TP.MS3683.PC821 T-Con board: N4TP546UHDPU2L_BO

                                          Last Sunday I was watching a dvd and fell asleep for about half hour, when I awoke the tv screen was black and couldn't get the dvd menu to show, so I changed the input to antenna and had sound but no picture, turned it off. I then got online and found this great site! ....read many troubleshooting tips and this...
                                          10-28-2024, 05:06 PM
                                        • sam_sam_sam
                                          Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
                                          by sam_sam_sam
                                          I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

                                          This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

                                          After all of...
                                          07-13-2024, 08:14 PM
                                        • JDC
                                          (SOLVED) - ONN 100012588 No Power, Then Rebooting After Main Board Change
                                          by JDC
                                          ONN 100012588
                                          Issue: No Power, Then Rebooting After Main Board Change

                                          Short answer: replace main board and power board
                                          Technical answer: replace main board and Q306 & Q307 on power board.

                                          Long answer:

                                          TV wouldn't turn on. Power switch was fine which means the main board isn't processing the power on signal. Replaced main board. TV turns on now but randomly reboots. Bad main board? EEPROM? Tried to pull main board and got a shock touching the corner of the board. That's weird. C334 (450V 10uf) capacitor is still holding a high charge....
                                          07-15-2022, 07:39 AM
                                        • Loading...
                                        • No more items.
                                        Working...