ue70ru6025k lcd cv-GN070HGJV1H BN41-2703A HELP
-
-
Hello, here is a UE50MU7000 with BN41-02568B (after an electricity jump):
- no stand by led light
- power supply has 9v outputs which go to mainboard
- without mainboard connected backlight works fine
- without backlight connected still no stand by led light
- dumped 24C512, 25Q40, 25Q80 (through CH341A programmer before finding this site), and flashed backup data from a UE40MU6102KXXH (which has same main board), this did not fix anything
After reading this thread, found out there is a specific way of flashing 25Q40, so I've placed all original backups back to their chips (also tried to restore header data in 25Q40, but it did not work)
and while doing what is in guide in 4th post, found out that QE is impossible to check. (edit: in NeoProgrammer V2.2.0.10 it's possible)
Is there also a special way of flashing 24C512 and 25Q80 like 25Q40 requires?
Can you please take a look at these files and see if there is anything wrong?
Can send a thanks thru PayPal if it will fix this issue.Comment
-
Hi , i have a samsung model ua32k5100 that has its memory image corrupted.
IC 805 W25Q40CL.
Board name BN94-10869Q.
i have tried several images the best ones are when tv comes with samsung logo for 1 second and then reboot and stays black.
original problem with my own image that tv wont turn on and all voltages are ok and the board is ok
can someone pls try to fix my original dump or give me one.
original dump attached .
Thanks a lot.Comment
-
Could you help me...
I have a Samsung UE55MU6102K with the following problem : I disconnect the motherboard from main power supply from and the backlight leds light up.
Then motherboard connected, standby led is on and current consuption is 18W.
Then trying to start the TV, the standby led is blinking once but TV don't start and standby led stay red.
Maybe the firmware in the IC SPI Flash W25Q40CL (IC1604) is corrupted.
The model of my TV is :
Power supply BN44-00807A
Main Board BN41-02568B / BN94-12765W
Panel CY-GM055HGLV3H... -
Hi all,
This is my first post here (I am very new to forums!) and I hope someone can help. I am looking for a full dump of the BIOS of a HP Proliant Microserver Gen 8 so that I can get this mini server running again. (BIOS version J06 2019-04-04, chip 25Q064A). I think my board was partially bricked after a failed BIOS update.
I got it second hand in this state and all the normal attempts at bios restoration have not worked. I have even desoldered the chip and tried to load the actual BIOS from HP, but it is missing some parts needed to boot the system.
I... -
Could you help me,I have a Samsung UE43MU6105K with the following problem, dead TV, when I disconnect the main power supply to logic board, the leds light up.
The model of my TV is UE43MU6105K
Main Board: BN41-02568B
BN94-12007Y
Could you help me to repair the dump please. Thank you.
... -
The Samsung S49CG934SU monitor does not power on - no LED indicator activity and no response to power button. However, when 21V power is connected, it immediately draws 0.8A of current with no display output. The motherboard processor gets warm, and there is continuous reading activity from the W25Q128BV BIOS chip.
Suspected Cause:
I suspect the BIOS may have been corrupted during a power interruption while updating the firmware. The official website provides firmware updates, but they can only be installed via USB flash drive.
Troubleshooting Attempts:
... -
Hello guys i really need help, i recently updated my DS-7208HGHI-K1 and it somehow got bricked, I've got it up and working now by flashing a new dump file i found but the serial number is really wrong and the uploader of the dump file probably intentionally did it.
I still have the bricked dump file is it possible to transfer the serial number of the "bricked dump" to the "working dump"?
Comment