Fsp300-60atv (pf)

[berreke54]

I have a PC smps FSP300-60ATV (PF) from Aopen with problem to start up.Only after several attempts it starts .
I found several elco's to be bad :
1) (c33?) 4700uF/10v FUHJYYU TMR (M) P10 CE 105°C VENT ø10mm L31mm
located at ?
2) (c32?) 4700uF/10v FUHJYYU TMR (M) P10 CE 105°C VENT ø10mm L31mm
located at the end of 3,3v ( to ground)
3) (c26?) 1000uF/10v FUHJYYU TNR (M) P10 CE 105°C VENT ø10mm L18mm
located at the end of 5v ( to ground)
4) (c23?) 1000uF/10v FUHJYYU TNR (M) P10 CE 105°C VENT ø10mm L18mm
located at ?
5) (c25?) 2200uF/16v FUHJYYU TMR (M) P10 CE 105°C VENT ø10mm L31mm
located at the end of 12v ( to ground)
6) (c28?) 3300uF/10v TEAPO A3 11/02 SEK 105°C ø10mm L26mm
located at the end of 5v ( to ground)
7) (c29?) 3300uF/10v JAMICON 245C1 TK 105°C ø10mm L30mm
located at ?
*******
I have made the choice to take RS to order new caps and to take panasonic as brand.
I chose to replace them with :
1) PANASONIC EEUFM1A472L : 4700uF/10v ø12,5mm L35mm
2) PANASONIC EEUFM1A472L : 4700uF/10v ø12,5mm L35mm
3) PANASONIC ECA1CHG102 : 1000uF/16v ø10,0mm L16mm
4) PANASONIC ECA1CHG102 : 1000uF/16v ø10,0mm L16mm
5) PANASONIC EEUFM1C222 : 2200uF/16v ø12,5mm L25mm
6) PANASONIC ECA1AHG332 : 3300uF/10v ø12,5mm L20mm
7) PANASONIC ECA1AHG332 : 3300uF/10v ø12,5mm L20mm

CAN ANYBODY GIVE ME ADVICE if I made THE good choice ?



Thanks

[berreke54]

Re: Fsp300-60atv (pf)

I wonder if there is a reason why I do not have any replies or advise I asked for??

[linuxguru]

Re: Fsp300-60atv (pf)

The Panasonic FMs are good choices. I'm not sure what the other Pannies are - perhaps some are FC? In that case, they're good choices too.

[370forlife]

Re: Fsp300-60atv (pf)

Its because it should have gone in the power supply discussion.

[berreke54]

Re: Fsp300-60atv (pf)

thanks for the advice

[Toasty]

Re: Fsp300-60atv (pf)

These are not low enough ESR nor high enough ripple handling:

[NHG Series]
3) PANASONIC ECA1CHG102 : 1000uF/16v ø10,0mm L16mm
4) PANASONIC ECA1CHG102 : 1000uF/16v ø10,0mm L16mm
Ripple = 560mA

6) PANASONIC ECA1AHG332 : 3300uF/10v ø12,5mm L20mm
7) PANASONIC ECA1AHG332 : 3300uF/10v ø12,5mm L20mm
Ripple = 1000mA

All should go with the FM series unless you have a height clearance issue.

3 & 4 - EEUFM1C102 - 20mm - ESR = .019 / Ripple = 2180mA

6 & 7 - EEUFM1A332 - 25mm - ESR = .015 / Ripple = 3190mA

Toast

[yanz]

Re: Fsp300-60atv (pf)

@ original poster
so, is the prolem solved by changing those capacitor (ie. there's no problem to startup again)?

[kc8adu]

Re: Fsp300-60atv (pf)

yes use the fm for all the parts you listed.
thats usually whats wrong with these fsp units.
its never good to see fuhkyyu caps in anything!

[Toasty]

Re: Fsp300-60atv (pf)

Probably not monitoring the post since his reply of 5/23. I think the forum default is to not receive emails of new posts. I sent him a PM.

Toast

[berreke54]

Re: Fsp300-60atv (pf)

i just received the parts and i'm going to replace it next week, i keep you informed later on
thanks

[berreke54]

Re: Fsp300-60atv (pf)

I replaced all these caps and with the ps tester everything looks fine : the ps starts instantly like it should.
I bought me a esr meter too ( atlas esr from peak ltd ) and mearured the caps that i replaced : the teapo and jamicon are good and the ones from fuhjyyu are all bad.
1.67 ohm,1.91 ohm,1.81 ohm,4.4 ohm,1.43 ohm.
I will place the ps back in the pc and hope it will last for a long time.
thanks for all the advice.

[lucky13]

Re: Fsp300-60atv (pf)

I replaced all these caps and with the ps tester everything looks fine : the ps starts instantly like it should.
I bought me a esr meter too ( atlas esr from peak ltd ) and mearured the caps that i replaced : the teapo and jamicon are good and the ones from fuhjyyu are all bad.
1.67 ohm,1.91 ohm,1.81 ohm,4.4 ohm,1.43 ohm.
I will place the ps back in the pc and hope it will last for a long time.
thanks for all the advice.

Wow, that's some kind of esr meter!

Maybe you can do a review and post here?