Re: Dell 3008wfp faulty power supply
Ok - test it again out of circuit.
Ok - test it again out of circuit.
-
Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740 -
Re: Dell 3008wfp faulty power supply
and how do I do that? Sorry for my noob-i-ness D:Comment
-
Re: Dell 3008wfp faulty power supply
I think this will be a double diode so if it has three legs
do the following test on one side and the middle then do it on the other pair ( middle and other side)
This test is from retiredcaps 2 sec to black guide which is interesting for anyone doing anything like this- start at post 20
https://www.badcaps.net/forum/showthread.php?t=10419
7.3) Bad Diode
-----------------
Diodes (D or ZD designation) can be bad. To test a diode in circuit,
a) put your multimeter in diode test mode
b) put your black lead on one side and the red lead on the other - record reading
c) reverse the leads - recording reading
A good diode should read 0.4V to 0.7V in one direction and 0L in the other. If you get a reading in both directionsPlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: Dell 3008wfp faulty power supply
Do I not need to hook up some kind of current to the diode for the test to work?Comment
-
Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: Dell 3008wfp faulty power supply
Your multimeter when set to diode test mode provides a small current through the diode. See
http://www.allaboutcircuits.com/vol_3/chpt_3/2.html--- begin sig file ---
If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.
We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.
Please do not post inline and offsite as they slow down the loading of pages.
--- end sig file ---Comment
-
Re: Dell 3008wfp faulty power supply
Greetings,
Count me too in the success stories list: last week the display died (completely: no blue/orange led).
Found D22 died in closed circuit state, today I replaced it with a STPS60170CT and now it's back working flawlessly. It costed me about 3€ and 2 hours of work.
Thank you all for this great thread.Comment
-
Comment
-
Re: Dell 3008wfp faulty power supply
SO:
Original D22 Readings:
Black Left, Red Centre: 007, Black Left, Red Right: 007
Red Left, Black Centre: 007, Red Left, Black Right: 007
Replaced D22 Readings:
Black Left, Red Centre: 1, Black Left, Red Right: 1
Red Left, Black Centre: 122, Red Left, Black Right: 1
Original D19 Readings: (potentially shorted one)
Black Left, Red Centre: 1, Black Left, Red Right: 1
Red Left, Black Centre: 052, Red Left, Black Right: 1
I applaud your commitment to helping people Lumberjack, I'm sure many people are grateful for the help!Comment
-
Re: Dell 3008wfp faulty power supply
You seem to have not done the test correctly?
First pair
Black Left, Red Centre:
Red Left, Black Centre:
Second pair
Black Centre, Red Right:
Red Centre, Black Right:
Where you have 1 do you mean 1 or Off ScalePlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: Dell 3008wfp faulty power supply
By 1 I assume it means off the scale, as it shows 1 when the probes arn't touching anything!
First pair (D22 Original (broken!))
Black Left, Red Centre:020
Red Left, Black Centre:020
Second pair
Black Centre, Red Right:030
Red Centre, Black Right:020
First pair (D22 Replacement)
Black Left, Red Centre:1
Red Left, Black Centre:150
Second pair
Black Centre, Red Right:150
Red Centre, Black Right:1
First pair (D19 (The shorted one))
Black Left, Red Centre:1
Red Left, Black Centre:070
Second pair
Black Centre, Red Right:070
Red Centre, Black Right:1Comment
-
Re: Dell 3008wfp faulty power supply
bump!
Comment
-
Re: Dell 3008wfp faulty power supply
[[[[[RETEST]]]]]]
First pair (D22 Original (broken!))
Black Left, Red Centre:000
Red Left, Black Centre:000
Second pair
Black Centre, Red Right:000
Red Centre, Black Right:000
First pair (D22 Replacement)
Black Left, Red Centre:1
Red Left, Black Centre:115
Second pair
Black Centre, Red Right:115
Red Centre, Black Right:1
First pair (D19 (The shorted one))
Black Left, Red Centre:1
Red Left, Black Centre:045
Second pair
Black Centre, Red Right:044
Red Centre, Black Right:1Comment
-
Re: Dell 3008wfp faulty power supply
"First pair (D22 Replacement)
Black Left, Red Centre:1
Red Left, Black Centre:115
Second pair
Black Centre, Red Right:115
Red Centre, Black Right:1"
Are you using the meter in Diode testing mode or using Ohm mode?
"115" is that MOhm, KOhms, Ohm, V?Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Dell 3008wfp faulty power supply
When you check semiconductor device for short, use Ohm function since bad semiconductor junction will act more like low Ohm resistor, it will no longer act like Diode any more.
D22 is OK.
Check D19 in Ohm mode to see what you get, so far it looks like it has very low Vf.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Dell 3008wfp faulty power supply
which probes on which side? and at what ohm setting? I have: 200, 2000, 20k, 200k, 2000k
on the 200 setting I got a reading of 69.9 for red left and black centre
I also got 69.9 for black centre red right!Last edited by fuus; 08-17-2012, 01:03 PM.Comment
-
Re: Dell 3008wfp faulty power supply
I just want to thank the major contributors to this thread - I'm in the same predicament and have got quite a lot to go on thanks to the posts here. Have ordered a pack of STPS60170CTs (minimum order of 5 :/) and will hopefully be taking a look at it this weekend. It's quite promising how many people have fixed the issue by changing this single component.Comment
-
Re: Dell 3008wfp faulty power supply
"on the 200 setting I got a reading of 69.9 for red left and black centre
I also got 69.9 for black centre red right!"
Now do the reverse:
black left and red center
black right and red centerNever stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: Dell 3008wfp faulty power supply
both get no reading what so ever.Comment
Now if we can get fuus fixed up; I'll be able to sleep again 
-
Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.
Upon bringing it home and plugging it up, it showed a standby light.
I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.
The screen seems to blackout and stay black, but with a flashlight I can see the display.
With my Playstation 4 connected via HDMI, and running a game I can hear sound.
Assuming... -
I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump
One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy... -
Hi everyone,
Looking for some advice or opinions on what to do with a monitor issue I’ve run into. Apologies in advance is this crossovers a few forum categories.
I have a Dell U3425WE, which I've recently replaced with another model. That said, the original unit is still fully functional in terms of the display — it works perfectly over HDMI and DisplayPort. However, the USB-C and Thunderbolt 4 ports have stopped functioning correctly. The Issue:- The 90W Thunderbolt 4 port (circled in the photo) no longer charges or powers any device, including laptops or MacBooks.
- There’s
Yesterday, 04:55 AM -
I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails
I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time... -
Hello all,
this is my first post, so if I make mistakes please do not hesitate to point them out, thank you in advance.
I got a Dell Latitude 5420 (Service Tag: 7RFM6D3, Motherboard: GDF40 LA-491P Rev.: 2.0 (A01)) which does not start and I want to repair it. These are the symptoms:
If the laptop is only connected to the AC adapter (battery removed):
When I press the power button, the keyboard backlight and the display backlight are turning on. Caps key light is lightning, but key does not respond to pressing it.
The power/battery...
Comment