I need help identifying this thermistor

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Assurance
    Member
    • Jun 2020
    • 16
    • u.lk
    #1

    I need help identifying this thermistor

    Hi all,

    sorry if this has been posted in the wrong group

    Im trying to replace this thermistor<<<10D-9 >>>> implies 10ohms, 9mm
    im not sure if this NTC or PTC ?

    I need help identifying this thermistor from
    rs online website and
    https://uk.farnell.com/w/c/circuit-p...ost=thermistor


    what will this be an ideal replacement fro RS ?


    Ive been chatting with RS online but theyve been very unhelpful
    Attached Files
    Tags: None
    • Spider1211
      Badcaps Veteran
      • Oct 2019
      • 532
      • Mauritius
      #2
      Re: I need help identifying this thermistor

      Almost all search result returns as NTC for 10D-9. What is the device used for? I assume its on the mains input side of a power supply; in this case it would be NTC and used to limit inrush current.

      This should be a good replacement: https://uk.farnell.com/ametherm/sl10...r9Wjd6oxzMXZLs
      Last edited by Spider1211; 06-09-2020, 10:07 AM.

        Comment

        • petehall347
          Badcaps Legend
          • Jan 2015
          • 4426
          • United Kingdom
          #3
          Re: I need help identifying this thermistor

          is it open circuit ?

            Comment

            • Assurance
              Member
              • Jun 2020
              • 16
              • u.lk
              #4
              Re: I need help identifying this thermistor

              Thanks ever soo much for your swift reply

              its part of a controller circuit

              Regards
              Attached Files

                Comment

                • budm
                  Badcaps Legend
                  • Feb 2010
                  • 40746
                  • USA
                  #5
                  Re: I need help identifying this thermistor

                  Related to this thread: https://www.badcaps.net/forum/showthread.php?t=85199
                  1) Why do you think it is bad?
                  2) 10D-9 is the NTC for inrush current protection. It is 10 Ohms 9mm Dia. https://www.ebay.com/itm/10pcs-NTC-1.../221405367958?
                  3) What is board not doing?
                  Last edited by budm; 06-09-2020, 05:13 PM.
                  Never stop learning
                  Basic LCD TV and Monitor troubleshooting guides.
                  http://www.badcaps.net/forum/showthr...956#post305956

                  Voltage Regulator (LDO) testing:
                  http://www.badcaps.net/forum/showthr...999#post300999

                  Inverter testing using old CFL:
                  http://www.badcaps.net/forum/showthr...er+testing+cfl

                  Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                  http://s807.photobucket.com/user/budm/library/

                  TV Factory reset codes listing:
                  http://www.badcaps.net/forum/showthread.php?t=24809

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • nmbb
                      Can not find Model/Value of Thermistor.
                      by nmbb
                      Machine: Autoclave.
                      Brand/Model: SANYO MLS-3780
                      Manual: (Sorry search option not working on this PDF)



                      Hello guys, this autoclave running with 2 thermistors already connected TH1 and TH3(on CN1,CN2 sockets). One for the water temperture and second one for chamber temperature. But there is another emtpy socket for optional third thermistor CN2 wich is for TH2 for object temperature. I wanna add the third thermistor TH2 to CN2 socket. But i can't figure what model/brand/value i need to use. In manual document, there is no info about TH1 and TH3 model number...
                      06-02-2022, 05:55 PM
                    • Use2bavolvo
                      Magic chef oven - thermistor ref voltage issue
                      by Use2bavolvo
                      I am having an issue with my wall oven temperature control is ~180f out of spec. The thermistor is measuring correctly but I noticed the ref voltage appears to be off. With the thermistor wires attached it's reading ~3.4vdc with the thermistor disconnected it's around I9.8vdc. my understanding is the temp is read off the resistance from the thermistor which leads me to believe the issue is with the ref voltage.

                      Another observation is the temp setting and readout at lower temps is way off meaning the oven thinks room temp is 300f and bake relay doesn't engage unless temp setting...
                      01-19-2023, 01:32 AM
                    • Quantum IC
                      Sony KDL-40BX450 LCD. Thermistor gets too hot 10 seconds after turning on the TV
                      by Quantum IC
                      Hello every one,
                      This TV came to me with the problem that it was totally dead.
                      The problem was the two MOSFETs and a fuse resistor in the power supply.
                      The original MOSFETs were KF7N50F and I repalced them with SLF65R700S2.
                      The original fuse resistor was 0.1 Ohm 1/2W. I didn't find a similar fuse resistor and I replaced it with 0.1 Ohm 5W ceramic resistor.
                      When I plug the TV the ST-BY LED turns on, when I press the power button on the TV, the ST-BY LED turns off and the TV doesn't turn on until the second time I press the power button is when the TV turns on,...
                      01-14-2022, 12:06 AM
                    • fab13
                      Thermistor exploded in two when turning on ps4 fat
                      by fab13
                      Hi there,

                      I have a fat PS4 with the fuse (5a) of the power supply which blows with each power on and there was a loud snap in the power supply and again the same problem after replacing the fuse.
                      I did not find a short circuit

                      The component that broke in two is an SCK 084 thermistor (See photo)
                      and measured at 11 ohm

                      So far I haven't received a thermistor.

                      Do you think that if I replace the thermistor and the fuse it should go away, because I have the impression that there is a strong current demand as soon as you press...
                      11-05-2022, 06:29 PM
                    • Adam Biderman
                      Nintendo switch HAC-CPU-20 help identifying resistors
                      by Adam Biderman
                      Good morning, I would appreciate help identifying resistors responsible probably for volume down / volume up buttons that I accidently knocked off while replacing fan connector. I enclose picture with location. Thank you for help in advance.
                      1 Photo
                      07-19-2025, 01:49 AM
                    • Loading...
                    • No more items.
                    Working...