Re: Lg49uj6200ua
I have two inbound. Neither one from a cracked screen tv supposedly. I will post results soon.
Thanks
LJ
I have two inbound. Neither one from a cracked screen tv supposedly. I will post results soon.
Thanks
LJ
-
-
Re: Lg49uj6200ua
Both inbound boards arrived and exhibited the same behavior. Boot up to LG splash screen then goes to setup screen to select language, time zone, etc. Once complete and I select OK, I get a brief white flash then blank screen and no reaction to remote. I tried disconnecting cables to t-con to see if it was somehow displaying setup otherwise..nothing.
SMPS and associated main and signal processing works for info burned onto eprom, not not from other main board inputs. If it was t-con, I would not get LG and setup screens clear as a bell. It has to be the main board.Comment
-
Re: Lg49uj6200ua
Ok, must be procedure for different model, wonder if hold down power button and push menu button on remote would work?Comment
-
Re: Lg49uj6200ua
Thats 5 mainboards right? wonder if theres some common fault with these or its something other than the mainboard?Comment
-
Re: Lg49uj6200ua
Did you test the tcon at all the test points? guess the tcon could only be partially working?Last edited by nomoresonys; 12-13-2018, 06:19 PM.Comment
-
Re: Lg49uj6200ua
Maybe check the rest of the electrolytic caps of the powerboard, then the blue ceramic caps.Last edited by nomoresonys; 12-13-2018, 06:42 PM.Comment
-
Re: Lg49uj6200ua
Could try heating your powerboard caps a little with a hair dryer, see if it comes on.Comment
-
-
Re: Lg49uj6200ua
I actually replaced the electrolytic Caps on SMPS..no difference. I tried two more main boards...same thing. I will have an SMPS today. This is very strange.Comment
-
Re: Lg49uj6200ua
Maybe test the little capacitors on tcon for shorts, diode mode.Comment
-
Re: Lg49uj6200ua
Well today I replaced the smps which made no difference. I have tried six main boards in this set. 5 of them did exactly what is in this video.
{https://drive.google.com/open?id=1qUL6X-nEcmPrf23UDNLq5J4-lN2SIbJ-}
The sixth one made it past this into the setup and would produce audio and video in the PIP screen in the INPUT SELECT tab.
The Tcon is actually two boards that are bonded to the panel ribbons so if one of them is bad, then the panel is bad. hard to believe that five main boards are all bad. All came out of freight damaged sets. One place in Houston says they run them in a set, but they have thousands of boards for hundreds of sets. They have been the easiest to deal with though.Comment
-
Re: Lg49uj6200ua
Ok, so you can do the initial setup right? try going to picture mode, set it standard and auto brightness to medium or low, turn down backlights to as low as you can stand it, see if it stays on, then maybe you can turn them back up a little if it stabilizes. Do not run tv in vivid mode, its a killer.Last edited by nomoresonys; 12-19-2018, 10:04 PM.Comment
-
Re: Lg49uj6200ua
Theres something odd going on with these tvs, must be a design flaw or they're using components that are not up to the task.Comment
-
Re: Lg49uj6200ua
I never make it that far in the setup, as shown in the video, except with one of the main boards. That one main board will let me into the menu and even display in a PIP mode, whatever is on the input selected..Until I try to go into operation full screen. Then I get the blank screen also as in the video.Comment
-
Re: Lg49uj6200ua
Ok, can you get to those settings on that board?Comment
-
Re: Lg49uj6200ua
I returned it for credit.Comment
-
Re: Lg49uj6200ua
I have now tried six main boards and a power supply board. Only other thing connected to the main board is a little interface board for the ON button. I wonder if it could be sending a signal to the main board that it does not like? I am going to replace it to see. There is nothing left but a ton of defective main boards. Hard to believe they are all bad.Comment
-
Re: Lg49uj6200ua
Here is a pic of the button interface boardAttached FilesComment
-
-
Re: Lg49uj6200ua
have you looked at the network interface, wifi maybe or ethernet?
If it has a wifi module, try removing it / disconnecting it. If it has an ethernet interface, try connecting to a network and repower.
Have you tried a different remote and / or new batteries?
I don't think you ever answered the "request" to try disconnecting the main board and seeing if the backlights stay on. IF so, did you check the "inv on" voltage signal? Perhaps the one you report (1.85) is low / borderline and when the system goes to "full operation" that value dips.Last edited by budwich; 12-26-2018, 12:27 PM.Comment
-
Hello everybody! Posting this in hopes somebody has some expertise that leads to a clear path of troubleshooting that saves me a lot of time!
My macbook has the flex cable problem, the one that prevents the screen turning on. Ive been dealing with this for the last 3 years. Last year it went dead and I managed to fix it following youtube tutorials. But my fix wasnt the best, the problem returned a month later. This week, it went dead again. I again tried to fix it.
This time the original cable broke too close to the screen, it can't be fixed without tearing the screen... -
Just had a customer bring in a M2 MBA A2681 that had had a screen replacement in April at another repairer. Since then, she has been getting intermittent kernel panics. It's an aftermarket screen, and of course it fails in diagnostics as the calibration hasn't been done. The error in the panic log is "No device added after powering on the rails".
It seems the original repairer has swapped the board and the screen to other MAC's, and said that it isn't a screen issue. From what I understand, by doing a quick search on Google, this is in fact a screen issue. The panic relates...07-31-2025, 08:37 PM -
Hi,
I have a iphone XS that came in for a screen replacement, the screen was badly cracked, and inside missing scues, on the back of the screen still the blue protector, the screen was a LCD. So we replaced the screen and all good, installed the screen and we noticed that pressing the screen with a bit of force but not excessive, the phone dies. After plugging the charger it turns back on, but again if you press it it dies. I open the phone again, and I can't see anything major, with the phone open, if I press on the logic board, battery, charging board, or even putting pressure on... -
Hello everyone, I’ve just been given a Samsung UE55JU6800K smart tv as it had white spots on the screen due to the led lenses falling off. After refitting them & putting the tv back together I thought it was a nice easy fix for a free bedroom tv , then I tried it before screwing the back into place. I realised that the right side of the screen was darker than the other side, I removed the screen again as I thought the backlights had failed but they are fine.
I put the screen back in place & turned it back on . The screen seemed to be ok again but different screens on the same... -
Hi all,
I'm becoming crazy trying to fix the Philips TV of my old man (model 43PUS6201/12 - the TV, not my dad). I've read again and again discussions about this and similar TV models, on badcaps (thanks so much !). I see no other option than asking for your help.
The symptom is simple : when I plug the power cord, the red "stand-by" LED does not light on anymore, and the TV powers-on neither with the remote control nor with the rear button. I guess at this point you immediately think at the 5V (or other voltage depending on the hardware) stand-by output......
Comment