-
Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809 -
Re: LG no picture
Hay, take a look at these two pics. See where the probe is pointing. Where the test points really stand out. "first pic" This is where I get.698 on all except the last two on right. Ok the second pic where the probe is. Should I get the same reading here. I checked several and can only get.698 on one. Others are around .7
Could it be the tcon.Attached FilesComment
-
-
Re: LG no picture
Yes 12v on tcon fuseComment
-
Re: LG no picture
Correction 6.98 not .698Comment
-
Hello all ~
Hope this finds you well. This LG 82UN8570AUD (April 2021 model) 4K UHD television has full audio capabilities but video is compromised / problematic.
When I picked up this large LG tv it had a full black screen upon startup. Previous owner said it just went black one day. No popping sound or anything else of note.
I got the display to work by taping off several traces of the right-hand side ribbon cable on the TCON that leads from TCON to PANEL. However, despite dozens and dozens of attempts to find the right combination / range of traces taped... -
Today I got a 65" TV from Hass company. It was not showing any picture. I taped the 6 lines of the Tcon FFC cable on the faulty side of the shade and the picture came but the display on the side where I blocked the pins was not showing properly. I checked the volts on the VGH point and -3.5 volts was abnormal, there should be about 28 to 30 volts on this point! There were +30 volts on the VGH point on the Tcon. I put a jumper on the source PCB from the Tcon side and saw, the raster started appearing on the display. I also tried soldering the 6 blocked pins but the picture did not come properly.... -
Good day, I have a TCL TV: Model 43s423. After turning ON the TV, the ROKU TV logo appears with fine lines over the whole screen, then after a while there are vertical bands in the middle of the screen top to bottom and the TV tries to update its firmware but I do not have the remote to connect it to my new network connection. Also the Power ON light blinks 2 times in quick succession. When I remove the ribbon on the right of the tcon board the left side of the screen shows but with fine lines. If I remove the left side ribbon and connect the right side ribbon the whole screen is blank with... -
hi guys, i need your help again...i have tcl u65x9006. while i was watching it become darker like when a movie ends, little by little the image disappear. now if i turn on i have back light on, after like 1 min i have also sound but no picuture. the back light is on i take off one at time the ldvs but nothing change always no picture. i tried to cover with a piece of paper the pin of ldvs i cover like 7 8 pins but nothing worked. the tv stay with no picture. there is a tcon board.i checked the voltage there on the fuse i have 11,8 volts. there is caps in shorts on the exit of the tcon i have... -
Laptop is HP Envy x360 13-bf0013dx, hp website link, it's an i7-1250U with 8 gig onboard ram.
Platform: ipa32 la-m024p rev 1b
Originally you'd plug power supply into it and it would take up to 1.2 amps and then drop to 200 milliamps and then go back up again to 1.2, staying all the while at 5 volts. Pressing power button would results in power LED blinking amber 3 times. 3.3 volt rail, 5.1 volt rail present, main power rail 8.8 volts. Power button test pads near EC chip 2.7 volts.
I found a short on the other side:
...10-04-2025, 05:03 PM
Comment