Tcon or bad panel or other!!!????

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • fharris1977
    Senior Member
    • May 2017
    • 132
    • United States
    #1

    Tcon or bad panel or other!!!????

    Hello. I have an RCA lcd tv and after I replaced the power supply, the screen comes on but I have 2 large vertical black lines going down the right side of the screen (Picture is included) I then changed the t-con board and I still get the same 2 black lines. They may be slightly larger with the new t-con board. Did I get a defective t-con board or is it a bad panel or something else? I do recall bad caps on a power supply on a samsung flat screen caused multicolored lines all over the screen. If anyone has experienced this problem please help me out. Thanks in advance.
    Attached Files
    Last edited by fharris1977; 10-30-2017, 05:16 PM.
    Tags: None
    • koka0011
      Member
      • Apr 2013
      • 30
      • Sri Lanka
      #2
      Re: Tcon or bad panel or other!!!????

      cof ic fault.may be loose connection

        Comment

        • geeforce
          Senior Member
          • Oct 2017
          • 87
          • Canada
          #3
          Re: Tcon or bad panel or other!!!????

          TAB Bonds?... open up frame and apply pressure above the lines... or search up tab bonds etc

            Comment

            Previous template Next

            Related Topics

            Collapse
            • x_orange90_x
              TCL 50S535 bad tcon or panel issue?
              by x_orange90_x
              Just bought this for 10 bucks yesterday hoping to fix it. The guy said water dropped inside from a dehumidifier hose and it started showing black and white vertical bars then went blank. When I got it home and turned it on it came on fine and displayed correctly but I was noticing faint vertical bars in the image. After a little bit I turned it off and back on and it was a black screen again. I opened it up to check for water damage and corrosion but didn't find anything of the sort. I cleaned the ribbons anyway and reconnected them but still got a blank screen. If I disconnect the right side...
              03-29-2025, 11:02 PM
            • Daren87
              Sony 8K XBR-75Z8H White Screen Vertical Bars Tcon Code. Help Needed🙏
              by Daren87
              Hello everyone,

              I've recently been given a Sony 8k Z8H. It's got a white screen with two vertical black bars. At times it's given me the 5 blink Tcon code. Testing voltage on the Tcon I can see some low or missing voltage. I've done a basic visual check of cables and the COF. Not seeing anything obvious. The original Tcon seemed to have good caps until turning it over. On the bottom I found maybe 10 caps with both sides of the caps shorting to ground. I thought ok these caps and likely other components on the Tcon are shorted so let's try a replacement Tcon. I just received the...
              08-13-2023, 03:25 PM
            • advant
              Driving a Sharp TCON/panel with a universal main board
              by advant
              This thread is about trying to get an Universal Main Board to work with a Sharp TCON and panel.

              I have a Sharp LC-46D85UN TV that has had a main board issue. Since this model is from 2009, I am not able to find an exact replacement of the main board. Instead, I decided to see if I can future proof this tv by getting a Universal Main Board (T53U21.2) from China to work with the Sharp TCON (CPWBX4291TPZA) and panel. The universal main board supports a 8 bit dual channel LVDS interface whereas the TCON requires a 10 bit dual channel LVDS input. I have modded the LVDS connector to match...
              02-03-2020, 12:25 AM
            • howardc64
              Samsung QN75Q6FNA backlight no display, red LED blink 2x, fault in panel
              by howardc64
              • Prior owner tried a replacement main board. No difference.
              • Samsung 2x red blinking standby LED = panel fault
              • Jumpered FB_TRDY_1 (pin 1 CN1300 left. main tcon->left side buffer boards) and FB_TRDY_3 (pin 95 CN1301 right. main tcon->right side buffer boards) This allows testing individual T-Con (on main board) connection to panel on this Samsung. Found fault on left side (viewing from rear of TV)
              • Each side has 2 buffer boards, disconnected left side flex between 2 buffer boards. Fault is on the left most board.
              • Tape masking eventually isolated to CN1300 pin 15 (CKV4_GOA) Display
              ...
              Yesterday, 10:54 PM
            • Ryan.man
              Macbook 2017 with touchbar (A1706) won't turn on after removing the screen
              by Ryan.man
              Hello everybody! Posting this in hopes somebody has some expertise that leads to a clear path of troubleshooting that saves me a lot of time!

              My macbook has the flex cable problem, the one that prevents the screen turning on. Ive been dealing with this for the last 3 years. Last year it went dead and I managed to fix it following youtube tutorials. But my fix wasnt the best, the problem returned a month later. This week, it went dead again. I again tried to fix it.

              This time the original cable broke too close to the screen, it can't be fixed without tearing the screen...
              02-04-2025, 12:23 PM
            • Loading...
            • No more items.
            Working...