Eeprom dump thread!
Collapse
This is a sticky topic.
X
X
-
Comment
-
EPROM help me please
television model; QN55Q70RAG
motherboard model; BN41-02695A
IC1502-IC1503-IC801- IC701 EMMCComment
-
Try this one, it's a dump from Akai though, the remote might not fit...Comment
-
-
Hello Lotas,
Thank you for the dump. I test the Akai dump but it doesn't work.
It could possible that the firmware is not the same on board TP.S506.PB801 and TP.S506.PB818.
I will test the 2nd file today. If i will send you the dump of my TV, could you fix it?
Thank a lotComment
-
Hello Lotas,
Thank you for the dump. I test the Akai dump but it doesn't work.
It could possible that the firmware is not the same on board TP.S506.PB801 and TP.S506.PB818.
I will test the 2nd file today. If i will send you the dump of my TV, could you fix it?
Thank a lotAttached FilesComment
-
Hello Lotas,
Thank a lot for your file, the TV works again. You are the best !!!
Thanks
Comment
-
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Hello Lotas,
Thank a lot for your file, the TV works again. You are the best !!!
ThanksComment
-
Comment
-
Hello again need firmware via usb because the tv goes to boot loop. It says not enought space and I couldn't make anything. Tv is Toshiba model 32la2063dg/2.1 PhotoComment
-
Comment
-
-
-
Looking for a working dump for the following Bush TV
Model: BUSH LE-40GCL-A1
Main: TP.SIS231.PT751
Screen: V400HJ6-PE1
Attached is the faulty dump from the TV.
Thanks for any helpAttached FilesComment
-
Comment
Related Topics
Collapse
-
Good day to all, I have a big problem. I can't find the eeprom dump for the Eizo CS2740 monitor. The device doesn't turn on, the indicator just lights up. It responded to connecting to the PC once. The update process started with the standard program and then disconnected from the computer. The computer doesn't detect it anymore. If anyone has an eeprom dump, please share.
-
Channel: Troubleshooting Computer Displays
07-26-2025, 03:24 PM -
-
by (0)_(0)Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
by my2k2Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.-
Channel: Troubleshooting Audio Equipment
07-01-2024, 09:04 PM -
-
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work....-
Channel: BIOS Requests ONLY!
-
-
by Ancient1Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... - Loading...
- No more items.
Comment