yokoono
Badcaps Veteran
Last Activity: Today, 01:52 AM
Joined: 04-29-2010
Location:
-
It could have been faster.😁😁... -
Try...Leave a comment:
-
Look.
1. Format a stick with FAT32
2. Create a folder called [B]pq [/B]on the stick
3. Unzip and put the 2 files in the folder
4. Turn on the TV, USB stick and type MENU 4725
5. Go to USB Operations and type OK on the remote control
6. Wait 10 seconds and exit the menu (return, back)
7. Turn off the TV from the remote control
8. Wait until the stby LED on the TV stops flashing
9. Unplug the TV and wait until the stby light goes out.
10. Take out the stick and turn on the TV.
If the image is not correct, repeat the operation
...Last edited by yokoono; 04-20-2025, 08:18 AM.Leave a comment:
-
Ask a friend for help.
...Leave a comment:
-
Save the panel profile from the TV and post it here to return the image.
1. Format a stick with FAT32
2. Create a folder called [B]downloadpq.mb211[/B] on the stick
3. Turn on the TV and type MENU 4725
4. Go to USB Options and type OK on the remote control
5. After 10 seconds you can remove the USB stick and you will have some files on the stick.
6. You post them here.Save the panel profile from the TV and post it here to return the image.
1. Format a stick with FAT32
2. Create a folder called [B]downloadpq.mb211[/B] on the stick
3. Turn on...Leave a comment:
-
1. Main code (17MBxxx) ??
2. Panel VES315WNVL-01 ??
3. What's wrong with the image ??
4. Type MENU 4725 and put the picture here....Leave a comment:
-
1. What is the problem with the TV?
2. What is the TV model?
3. What is the panel code (VES315xxxx-xx-xx)?...Leave a comment:
-
It happens to others too.😀Leave a comment:
-
NO....Leave a comment:
-
Save the profile from the TV.
1. Format a stick with FAT32
2. Create a folder called [B]downloadprofile.mb97[/B] on the stick
3. Turn on the TV and type MENU 4725
4. Go to USB Options and type OK on the remote control
5. After 10 seconds you can remove the USB stick and you will have some files on the stick.
6. You post them here.
There are 17MB97 motherboards that DO NOT HAVE WIFI.Save the profile from the TV.
1. Format a stick with FAT32
2. Create a folder called [B]downloadprofile.mb97[/B] on the stick
3. Turn on the TV and...Last edited by yokoono; 04-01-2025, 03:17 AM.Leave a comment:
-
Rewritten NAND memory or another motherboard. It could also be a hardware problem.
Nand memory cannot be rewritten with CH341A....Leave a comment:
-
Theoretically the TV should start by itself with the first installation. If it doesn't, the software on the stick cannot be installed. The SPI memory must be rewritten with the programmer or the NAND memory. I don't have any other software.
Try another stick with a smaller capacity (max. 16Gb).Leave a comment:
-
1. Format the stick with FAT 32
2. Unzip and put the files on the stick.
3. PRESS AND HOLD the OK button on the remote control
4. Plug the TV into 220v.
5. The stby LED on the TV flashes slowly and then quickly. When it flashes quickly RELEASE the OK button.
6. Wait for it to finish. It may take up to 5 minutes....Leave a comment:
-
Update for youtube. Install with MENU 1505....Leave a comment:
-
For USB it is not good?...Leave a comment:
-
1. Press and hold the OK button ON THE REMOTE CONTROL.
2. Plug the TV into 220v
3. The STBY LED flashes slowly and then quickly.
4. When it flashes quickly, release the OK button and wait for it to finish.
It may take up to 5 minutes....Leave a comment:
-
Or this ??...Leave a comment:
-
Look:...Leave a comment:
-
Cod main (17MBxxx) ???
If I don't have a profile, save the panel profile from the TV and post it here.Leave a comment:
-
Try...Leave a comment:
No activity results to display
Leave a comment: