-
-
Re: Eeprom dump thread!
Anyone, can help me with EEPROM, please?
Looking for:
WALKER WPS3219SM
Mainboard: 17MB211S
Chip: Winbond 25Q16JVSIQ
Panel model: VES315WNDB-2D-N21
Thank you in advance...Comment
-
Re: Eeprom dump thread!
Try (Toshiba). Main 17MB211S panel VES315WNDB-2D-N21Comment
-
Re: Eeprom dump thread!
Try this too. It is for 17MB211S panel VES315WNDS-2D-N21. If the image is returned I have the profile saved for fixing.Comment
-
Re: Eeprom dump thread!
I think there is another problem on the motherboard. Most often problems with dc-dc converters or processor. See also if the flash memory is powered by 3.3v.
What are the symptoms of television?Last edited by yokoono; 09-12-2020, 10:04 AM.Comment
-
Comment
-
Re: Eeprom dump thread!
Don't confuse eeprom memory with flash memory !!!. They are different. See what memory you rewrote. The software is for flash memory, spi.Comment
-
Comment
-
Re: Eeprom dump thread!
How does the defect manifest itself?Comment
-
Re: Eeprom dump thread!
TV not turning ON. When you turn TV ON, RED light up and stay solid. When you push ON button, RED light blinks 2 times and stay solid. Then blinks 2 times again and stay solid. And does this all the time.
PS.: Backlight I checked with the mainboard from Panasonic TV. Backlight working, just can't turn ON the TV.Comment
-
Re: Eeprom dump thread!
Heat the processor to 230 degrees for 1 minute and see what it does.
I think the motherboard has a hardware issue not a software one.
You can replace the memory with another new memory.Last edited by yokoono; 09-12-2020, 10:56 AM.Comment
-
Re: Eeprom dump thread!
Heated for 1 min at 230 degrees. Nothing. Still the same problem...
Do you mean I have to replace Winbond 25Q16JVSIQ with new one?Comment
-
Re: Eeprom dump thread!
Try. Rewritten. I have no other ideas.Comment
-
Comment
-
Blaupunkt w40/58j-gb-fhcup-eu memory dump
Hello, i need memory dump for this tv. the mather board t.msd309.8b 10304 and panel lta400hm07. thanks.Comment
-
Re: Eeprom dump thread!
hello everyone i just got this set in...37 inch Telefunken chassis... 40-1MS82D....I dont have the panel number...I need the dump for this board....thanks in advanceComment
-
Re: Eeprom dump thread!
Anyone at homeComment
-
Hello, This might be a long shot, but I'm looking for an EEPROM dump for a HP Photosmart C4280 All-in-one printer.
The printer seems to be in cartridge alignment mode. Sometimes it print the alignment page and then hangs during the scanning step, sometimes it hangs during the printing process and sometimes it hangs during the boot process. If I let it idle for a while then it flashes the back-light of the top screen and there's a letter E. Bottom screen is asking me to restart it to no avail. I have to remove the power cable from the printer for a couple of minutes to make it work...02-17-2022, 09:09 PM -
Good day to every one,
I have AVR 171 the IC1504 (24C32) eeprom is corrupted not able to read.
Does anybody have an eeprom dump file? I really appreciate any help.
Thanks in advance.07-01-2024, 09:04 PM -
P14s Gen 2
HT4B0/HP4B0/HT5B1/HT4B2
NM-D352 Rev 1.0
sn PF-35P15W
Requesting thunderbolt dump
also attached is the tbt dump. I extracted the bin from the cap file and modified it, not sure if it's correct. also didnt work.... -
Hi
I was working all day on a 42" with no backlight = Driver is bad . LED Tester. Image exists
As I was reassembling, I discovered faults on the screen ( used the LED Tester to power the strips).
Right distribution board, 2 Flexs, near them:
The one near the center has 1" line on screen. Pressing on the board-side or Panel side of the Flex bonding place results in some change, I sensed heating one time, but main fault line remains
The other, pressing on the Panel to the Chassey and the lines disappears 99.99%
I... -
Comment