Lg 50PA650t. No picture.

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Ice203
    Senior Member
    • May 2015
    • 99
    • Uk
    #1

    Lg 50PA650t. No picture.

    Hi. Just been give the above TV. Has sound but no picture.
    Tried the flash light test and can't c any image.
    So no wondering what I need to test next.
    Thxs
    Tags: None
    • CapLeaker
      Leaking Member
      • Dec 2014
      • 8325
      • Canada
      #2
      Re: Lg 50PA650t. No picture.

      https://www.badcaps.net/forum/showthread.php?t=39740

        Comment

        • Hamie
          Badcaps Legend
          • Apr 2014
          • 1383
          • UK
          #3
          Re: Lg 50PA650t. No picture.

          Is this not a plasma??

          Why would you do a flashlight test on a plasma?

            Comment

            Previous template Next

            Related Topics

            Collapse
            • JJAAMM
              SAMSUNG UN55KS9000F picture fades then distorts into vertical lines after 20 seconds
              by JJAAMM
              This was my main TV for the last 6 years. I'm not inclined to throw out a $2600 TV so quickly so I'm trying to investigate the issue.

              Problem
              TV was disconnected from power for 6 months during construction. When I plugged it yesterday picture was fine, after 30 seconds it dimmed then started developing horizontal lines, picture then starts to ghost vertically until it degrades into vertical streaks. TV always displays a perfect picture when cold. I can unplug TV for 5 minutes and plug it back in and picture is restored for 20 seconds. I can also keep it in standby mode...
              07-06-2023, 06:01 AM
            • chth96
              How Can I test PWM DM0365R?
              by chth96
              Hello
              I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
              So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
              I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
              I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
              06-18-2025, 04:14 PM
            • Mgiffune
              Samsung UN60EH6000F Black Screen, Backlight and Sound Good. Power Cycle Returns Picture
              by Mgiffune
              I have a 60 inch Samsung UN60EH6000F flatscreen TV. The screen went black a few months ago Sound is good, backlight is good, no menu. I replaced the TCon board with a used board purchased from Ebay. It worked fine for a 3-4 months, then the screen started ‘fading' back. Once again, sound is good, backlight is good, no menu. However, this time the picture looks fine for about 10-15 minutes, then fades back. If I power cycle the TV, the display reappears, for another 10-15 minutes, then fades black again. Repeatable ever time.

              I ordered a supposedly ‘new' Tcon board this time, and              ...
              06-09-2024, 10:28 AM
            • khelane
              test active pfc power with lamp test
              by khelane
              Hello
              I have a big problem and that is that in some cases when repairing active pfc power supplies I cannot work with a test lamp. I can only get help with 5 volts standby and for starting and starting I have to work without a lamp and this way there is a possibility of parts exploding and other parts being added.
              Sometimes with a multimeter test the problems can be reduced to some extent, but I had several cases that had to be tested on and online and recently two varistors exploded. They had terrible resistance because the power supplies were over 800 watts.
              Is there a way...
              06-03-2025, 01:00 AM
            • chronic519
              Mats / mods: detected and repaired GPU fault. Cant seem to test after!
              by chronic519
              Hello.

              GPU came in, green lines. Spent lots of time using to get the Mats / mods drive working (found on youtube).
              Found issue with a RAM block
              Replaced, green lines gone.
              Trying to test again, assuming getting the false positive. Originally had over 1K on a single bank. Now getting tosses low between banks.
              Used a good card to test and same results low errors 32+.

              I am just search for some form of command to do a full test on the GPU.
              I just ran the mats command with my good GPU and passed after roughly 40 min.
              The repaired one, ran...
              05-20-2025, 07:56 PM
            • Loading...
            • No more items.
            Working...