SHARP LC-46D65E Dead power led blinking twice

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ronhayes
    TV Engineer
    • Mar 2014
    • 458
    • UK

    #21
    Re: SHARP LC-46D65E Dead power led blinking twice

    Update so far on this set.
    (received remote from Tom this morning how goods that thank you Tom)
    After switching set on by power switch on TV with AC lead installed, Original fault displayed green Power LED light on then turned orange flashing orange for 9 flashes then turns green then you hear buzzing noise back lights flash on/off then Power LED flashes twice repeatably. I then pressed menu on the remote and the Power LED flashes red twice and the OPC LED flashes green 5 times . The first 2 flashes are in sequence with the 2 red flashes of the Power LED.
    Now looking at chart on the service manual this indicates Panel power supply error ?
    Now giving that i was measuring 3.19v on pin 12 of PD1 connector would i be right in assuming that the fault is on the main av board and not on the power board ?

    Comment

    • budm
      Badcaps Legend
      • Feb 2010
      • 40746
      • USA

      #22
      Re: SHARP LC-46D65E Dead power led blinking twice

      You do have 12V for panel:
      https://www.badcaps.net/forum/showpo...9&postcount=14
      So check the Voltage at the T-CON fuse.
      Never stop learning
      Basic LCD TV and Monitor troubleshooting guides.
      http://www.badcaps.net/forum/showthr...956#post305956

      Voltage Regulator (LDO) testing:
      http://www.badcaps.net/forum/showthr...999#post300999

      Inverter testing using old CFL:
      http://www.badcaps.net/forum/showthr...er+testing+cfl

      Tear down pictures : Hit the ">" Show Albums and stories" on the left side
      http://s807.photobucket.com/user/budm/library/

      TV Factory reset codes listing:
      http://www.badcaps.net/forum/showthread.php?t=24809

      Comment

      • ronhayes
        TV Engineer
        • Mar 2014
        • 458
        • UK

        #23
        Re: SHARP LC-46D65E Dead power led blinking twice

        Having trouble locating T-CON fuse ?
        Also looked in manual for T-CON layout bit vague to say the least could do with pointer where located on T-CON board !

        Comment

        • budm
          Badcaps Legend
          • Feb 2010
          • 40746
          • USA

          #24
          Re: SHARP LC-46D65E Dead power led blinking twice

          Check those FLxxxx:
          http://assets.shopjimmy.com/media/ca...pxc-bottom.jpg

          http://www.shopjimmy.com/sharp-cpwbx...con-board.htm#
          Never stop learning
          Basic LCD TV and Monitor troubleshooting guides.
          http://www.badcaps.net/forum/showthr...956#post305956

          Voltage Regulator (LDO) testing:
          http://www.badcaps.net/forum/showthr...999#post300999

          Inverter testing using old CFL:
          http://www.badcaps.net/forum/showthr...er+testing+cfl

          Tear down pictures : Hit the ">" Show Albums and stories" on the left side
          http://s807.photobucket.com/user/budm/library/

          TV Factory reset codes listing:
          http://www.badcaps.net/forum/showthread.php?t=24809

          Comment

          • ronhayes
            TV Engineer
            • Mar 2014
            • 458
            • UK

            #25
            Re: SHARP LC-46D65E Dead power led blinking twice

            Not sure if this scan will be clear enough to see but if the ones i have circled are correct i am getting 0v either side ?

            Click image for larger version

Name:	Scan.jpg
Views:	1
Size:	659.0 KB
ID:	1965306

            Comment

            • ronhayes
              TV Engineer
              • Mar 2014
              • 458
              • UK

              #26
              Re: SHARP LC-46D65E Dead power led blinking twice

              Then 12.04v from PL plug pin 1 that goes to P7003 I-CON board drops to 0v when set buzzes back lights flash on/off then power LED flashes ?
              Would this point to the I-CON board being faulty ?

              Comment

              • tom66
                EVs Rule
                • Apr 2011
                • 32560
                • UK

                #27
                Re: SHARP LC-46D65E Dead power led blinking twice

                I-CON or T-CON?
                Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                Comment

                • ronhayes
                  TV Engineer
                  • Mar 2014
                  • 458
                  • UK

                  #28
                  Re: SHARP LC-46D65E Dead power led blinking twice

                  I have also measured this voltage with ribbon cable from T-CON board to LCD removed one then reinserted and removed the other and then removed both , the voltage dropped to 0v on all occasions. Would this point to T-CON faulty?

                  Comment

                  • ronhayes
                    TV Engineer
                    • Mar 2014
                    • 458
                    • UK

                    #29
                    Re: SHARP LC-46D65E Dead power led blinking twice

                    T-CON i am on about Tom sorry should read what i am typing.
                    Are their any known faults on these boards or is it swap board only?
                    If it is a swap board maybe you have a T-CON board Tom?

                    Comment

                    • ronhayes
                      TV Engineer
                      • Mar 2014
                      • 458
                      • UK

                      #30
                      Re: SHARP LC-46D65E Dead power led blinking twice

                      According to the service manual power LED flashing red twice and the OPC LED flashing 5 times is a power panel fault? But giving that i have 12.04v at switch on and the dropping at error point does this mean main processor is switching this 12.04v off or is the T-CON taking it to ground? or is it a power board fault ?

                      Comment

                      • tom66
                        EVs Rule
                        • Apr 2011
                        • 32560
                        • UK

                        #31
                        Re: SHARP LC-46D65E Dead power led blinking twice

                        I had a panel power fault on my LC-52XL2E when I pinched a ribbon cable between the two panel boards.
                        Replacing the ribbon cable fixed the fault - although the fault was originally caused by me pinching it while putting the LCD back together...
                        Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                        For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                        Comment

                        • ronhayes
                          TV Engineer
                          • Mar 2014
                          • 458
                          • UK

                          #32
                          Re: SHARP LC-46D65E Dead power led blinking twice

                          Sorry Tom
                          I am a bit unsure what you mean?
                          Do you mean you took them out and replaced ?
                          Or do you mean you squeezed the ribbons and how ?

                          Comment

                          • tom66
                            EVs Rule
                            • Apr 2011
                            • 32560
                            • UK

                            #33
                            Re: SHARP LC-46D65E Dead power led blinking twice

                            They are ribbons that connect between the parts of the LCD.
                            One centre board with two ribbons, then ribbon cables each side to left and right.
                            Where the tabs connect.
                            This fault could be caused by liquid damage to the tabs - although I'd expect the fault to go with the cables disconnected.
                            Maybe check the main board schematic and see if you can fool the panel power detect algo - might help eliminate t-con/etc.
                            Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                            For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                            Comment

                            • ronhayes
                              TV Engineer
                              • Mar 2014
                              • 458
                              • UK

                              #34
                              Re: SHARP LC-46D65E Dead power led blinking twice

                              Looking at schematic i can see a IC 2003 on main board on this IC there are one pin marked DET_POW with a line leading to it written on that is DET_PNL_12v and i can also see a pin on the same IC 2003 marked up ERR_PNL with line leading to it marked up ERR_L This line is coming from p2603 on main board which is connected to LB1 (EU) plug on power board. It has six wires on it and marked up inver 1 to 6.
                              Would i disconnect the pin on IC 2003 for DET_12v or isolate the lead on plug p2603 marked ERR_L ?

                              Comment

                              • tom66
                                EVs Rule
                                • Apr 2011
                                • 32560
                                • UK

                                #35
                                Re: SHARP LC-46D65E Dead power led blinking twice

                                What about that cable that goes between the main board and T-con board, but it's not an LVDS cable? I think that has an error indicator on it... IIRC, when I disconnected that on an LC-32DH66E it threw out a panel power detect error.
                                Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                Comment

                                • budm
                                  Badcaps Legend
                                  • Feb 2010
                                  • 40746
                                  • USA

                                  #36
                                  Re: SHARP LC-46D65E Dead power led blinking twice

                                  Can I see the pictures of the whole back side of the TV so I can see the cables Tom is talking about?
                                  The service manual does not show how all the boards are connected together.
                                  Last edited by budm; 05-19-2015, 10:05 AM.
                                  Never stop learning
                                  Basic LCD TV and Monitor troubleshooting guides.
                                  http://www.badcaps.net/forum/showthr...956#post305956

                                  Voltage Regulator (LDO) testing:
                                  http://www.badcaps.net/forum/showthr...999#post300999

                                  Inverter testing using old CFL:
                                  http://www.badcaps.net/forum/showthr...er+testing+cfl

                                  Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                                  http://s807.photobucket.com/user/budm/library/

                                  TV Factory reset codes listing:
                                  http://www.badcaps.net/forum/showthread.php?t=24809

                                  Comment

                                  • ronhayes
                                    TV Engineer
                                    • Mar 2014
                                    • 458
                                    • UK

                                    #37
                                    Re: SHARP LC-46D65E Dead power led blinking twice

                                    I have tried pulling it i still get the same error.

                                    Comment

                                    • ronhayes
                                      TV Engineer
                                      • Mar 2014
                                      • 458
                                      • UK

                                      #38
                                      Re: SHARP LC-46D65E Dead power led blinking twice

                                      Here is a couple of pictures of the complete rear of the set .
                                      Click image for larger version

Name:	20150519_181131_resized.jpg
Views:	1
Size:	236.6 KB
ID:	1965361

                                      Click image for larger version

Name:	20150519_181122_resized.jpg
Views:	1
Size:	214.4 KB
ID:	1965360

                                      Comment

                                      • budm
                                        Badcaps Legend
                                        • Feb 2010
                                        • 40746
                                        • USA

                                        #39
                                        Re: SHARP LC-46D65E Dead power led blinking twice

                                        Man! that is lots of cables to the T-CON.
                                        Never stop learning
                                        Basic LCD TV and Monitor troubleshooting guides.
                                        http://www.badcaps.net/forum/showthr...956#post305956

                                        Voltage Regulator (LDO) testing:
                                        http://www.badcaps.net/forum/showthr...999#post300999

                                        Inverter testing using old CFL:
                                        http://www.badcaps.net/forum/showthr...er+testing+cfl

                                        Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                                        http://s807.photobucket.com/user/budm/library/

                                        TV Factory reset codes listing:
                                        http://www.badcaps.net/forum/showthread.php?t=24809

                                        Comment

                                        • tom66
                                          EVs Rule
                                          • Apr 2011
                                          • 32560
                                          • UK

                                          #40
                                          Re: SHARP LC-46D65E Dead power led blinking twice

                                          The smaller 4 pin one carries power to the T-con (Sharp do not use the LVDS cable for T-con power), the larger one carries some control signals, I believe related to gamma voltage programming as the gamma voltages can be adjusted from within the service menu on many Sharp TVs.
                                          Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                          For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                          Comment

                                          Related Topics

                                          Collapse

                                          • Tynan Dill
                                            Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                                            by Tynan Dill
                                            I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                                            Upon bringing it home and plugging it up, it showed a standby light.

                                            I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                                            The screen seems to blackout and stay black, but with a flashlight I can see the display.

                                            With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                                            Assuming...
                                            11-22-2024, 01:46 PM
                                          • PantherDave
                                            Microsoft Surface Pro (5th gen) model 1796 - no power
                                            by PantherDave
                                            Hi all!

                                            I'm trying to troubleshoot a Microsoft Surface Pro (5th gen) model 1796 that won't power on. Motherboard model is M1007506-015. My priority is retrieving data, but the SSD is integrated so it looks like if I can't repair it it'll need to go to a data recovery company. I've done a little basic board repair before, but nothing this advanced until now. So please forgive my ignorance in advance. 😅

                                            I found the boardview for this laptop in the forums here, and am able to open it on my PC with FlexBV.
                                            https://www.badcaps.net/forum/troubl...-hardware-devi...
                                            05-29-2024, 02:01 PM
                                          • GLISIT
                                            Asus Probook P5440UF-XB74 power issue
                                            by GLISIT
                                            Hi all,

                                            TL;DR - this laptop is driving me nuts with the oddball power-related behaviors. Appreciate any insight you can provide!


                                            I'm experiencing a power issue on an Asus Probook P5440UF-XB74. Although I've worked with electronics and computers for decades, this is my first attempt at getting into motherboard-level component troubleshooting. Any help the community can provide is greatly appreciated!

                                            A few weeks ago I was using the laptop (on battery power) for a Zoom meeting. The battery was running very low (long meeting) but I wasn't worried about...
                                            01-16-2025, 02:29 PM
                                          • Andreas_de
                                            Power supply Manson NTP-5561 (5661) LCD controller dead - PIC18F87K90 HEX dump required
                                            by Andreas_de
                                            Hello!

                                            i got a damaged Manson NTP-5561 (60V, 1,6A DC output) and and the main issue is that the controler IC for the LCD display has a short. The controler IC PIC18F87K90 is mounted on the back of the back of the LCD. Vss-Vdd = 3 Ohm. The 5V and 3,3V power line was killed as well, but that is not a problem. A new LDO 3,3V and 5V 7805 is already ordered.
                                            Replacing the PIC18F87K90 is necessary but that makes no sense without having the HEX dump of the new controler.

                                            Does anybody have such a power supply and could do a HEX dump of the Flash and EEPROM memory?
                                            ...
                                            04-12-2025, 10:38 AM
                                          • sam_sam_sam
                                            Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
                                            by sam_sam_sam
                                            I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

                                            One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
                                            03-31-2024, 02:12 PM
                                          • Loading...
                                          • No more items.
                                          Working...