Panasonic TH-P46G10A

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • UND312DOG
    Senior Member
    • May 2014
    • 63
    • Australia

    #41
    Re: Panasonic TH-P46G10A

    Here
    Attached Files

    Comment

    • tw2005
      Badcaps Legend
      • Oct 2011
      • 6457
      • Australia

      #42
      Re: Panasonic TH-P46G10A

      Yep, power off and reseat last ribbon on the SD

      Comment

      • UND312DOG
        Senior Member
        • May 2014
        • 63
        • Australia

        #43
        Re: Panasonic TH-P46G10A

        Perfect. Everything up and running like new again. Thanks again for all your help mate. Appreciate it a lot. $62 to fix a busted TV. Yeeeew.

        Comment

        • tw2005
          Badcaps Legend
          • Oct 2011
          • 6457
          • Australia

          #44
          Re: Panasonic TH-P46G10A

          Originally posted by UND312DOG
          Perfect. Everything up and running like new again. Thanks again for all your help mate. Appreciate it a lot. $62 to fix a busted TV. Yeeeew.
          good to hear.

          Would not hurt to get back to payless and give them some positive feedback.

          i genuinely think he tries his best.

          believe it or not the boards I got and reported good, one turned out shorted and the other was wrong version. Seems like he's going to do the righty and replace them, yet to be confirmed.

          being away for 2 months did not help.

          Comment

          Related Topics

          Collapse

          • cind12
            GTX 1080 TI Gigabyte Aorus low resistance on vmem
            by cind12
            Hi guys, i was wondering, i've got 9Ohms on Vmem, one of the mosfet was shortet to ground, so i've desoldered hi and low mosfets nad still low res, then i removed all of the memory chips, and the resistance is still low, so did you had maybe a card with that low res on memories, and the card was working fine ?
            Removed the U1866Q and still without result, i dont have thermal cam so can't see where is hot spot when incjeting voltage.
            The resistance on core is ok 0.1Ohm ((Power 0.8V when on)
            Resistance on 12V 4K ohms (Power present when on)
            Resistance on 12V PEX 4K ohms...
            12-08-2023, 09:09 AM
          • chth96
            How Can I test PWM DM0365R?
            by chth96
            Hello
            I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
            So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
            I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
            I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
            Yesterday, 04:14 PM
          • Nagy Daniel
            Lowest possible resistance on laptop motherboard rail - Guide Table request
            by Nagy Daniel
            Hi, I'm Daniel, and I'm new to the world of repairing motherboards.

            I would like to create a table, or more likely a guideline about the voltage rails and their possible resistance rail.

            I know that the motherboard design has a very big depend on the rail's resistance, but I would like to know what is the smallest value for a rail that can be acceptable. For example, I heard that some new gaming motherboards can have 0,5 Ohm resistance on the GPU rail, but on an older type, it could be a sign of a shorted GPU rail.

            So, I generated a table with AI so I can...
            03-04-2025, 08:24 AM
          • Andre Gilbert
            Panasonic TC-P55ST50 8 blinks then no blinks
            by Andre Gilbert
            Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
            Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.

            TV Model: Panasonic TC-P55ST50
            ...
            11-20-2024, 08:52 PM
          • gigigi
            Panasonic tx-55cx802b stuck on panel test mode
            by gigigi
            Panasonic tx-55cx802b stuck on panel test mode.
            It was working normally but few days ago some of the LED reflectors fall off.
            I've opened it up carefully, re-glued, while it was open switched it on to test LEDs.
            Then carefully assembled back.
            After plugging in to power remote does not work.
            Using power button on the TV it turns on but gets itself into a panel testing mode: white, gradient, red, gradient, blue, gradient, green and so on switching between colours.

            Anyone knows how to get out of this panel testing mode?

            I've tried so...
            06-20-2021, 07:06 AM
          • Loading...
          • No more items.
          Working...