so I got this tv, when I press power the green light will come on for a second then goes red 8 flashing blinks, nothing else
-
-
Re: sony kdl-40v3000 lcd 8 red blinks?
An 8X blink code is Speaker protection, The speaker connections on the au board are monitored for dc voltage, if this is detected the tv will shut down -
Re: sony kdl-40v3000 lcd 8 red blinks?
That means you have Class D power amplifier failure.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: sony kdl-40v3000 lcd 8 red blinks?
Yes. Did you hear it makes any funny sounds before it goes into 8X error?
You see this board in your TV.
http://www.shopjimmy.com/sony-a-1433-191-a-au-board.htm
http://www.shopjimmy.com/sony-a-1433...rd-rebuild.htmLast edited by budm; 05-12-2014, 11:13 AM.Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
Re: sony kdl-40v3000 lcd 8 red blinks?
I have that board yesComment
-
Re: sony kdl-40v3000 lcd 8 red blinks?
One thing to check is that the speaker wires are not shorted to the metal chassis anywhere, I did have one that the wires were pinched between the plastic and the metal chassis, as soon as the volume was turned up the tv went into shutdowm. If thats not the cause then the AU board is at faultComment
-
Re: sony kdl-40v3000 lcd 8 red blinks?
I bought a set with this power supply totally dead, the only problem I can find D907 &D911 seem to be reading short. I recommend checking these for this faultComment
-
Hello,
I have problem with SONY 55X90J. After several check status is as below;
1. Running power board as stand alone:
TCON_12V =~ 12.6V
EVDD V On Max 24V= 19V.
2.Running power board with TCON as stand alone:
Effect as below, attched.
3. When bottom LVDS cable is disconnected no blinks, but of course no TCON 12V and EVDD.
"I'm almost sure it's a defective panel, but maybe someone has encountered a similar issue on their screen.
Best regards.... -
Hi everyone. First post on Badcaps!
I am trying to fix a Sony 940E from 2017 that either starts normally (and works perfectly until turned off) or goes straight to the 6 blinks error code without showing anything on the screen. It is frustrating to know that it can still work perfectly but is barely usable because of the difficulty starting it up. I am willing to try to short the BL_ERR but I would like to avoid that if possible. Does anyone have a view on this? Thanks a lot.... -
I was asked to look at a Sony KD-55X8509C as it was not powering on, no lights.
On inspection, there was no physical issues.
I seated all cables and repowered the TV, then the LED light flashed Green / Amber.
- this seems to indicate repairing required, done by Firmware update.
so downloaded the latest Firmware from Sony website and wrote to 4Gb USB drive.
Inserted the drive and repowered the TV.
LED changed to white flashing/pulsing ... and it sat there for over an hour.
i was unsure what was happening so repowered the TV and now it just... -
Hi everyone!
I have a Sony KD-65A1 TV with a fault – 4 red LED blinks. After disassembly and visual inspection, I found that the G76 power board and DKA board had been replaced. It is also possible that TCON was replaced, but I am not sure – there are a few marker marks that could be factory-made.
Based on assumptions, the previous service attempted to solve the issue by replacing potentially faulty components. I decided to investigate further, found a service manual, and figured out a way to power up the power supply unit autonomously and put the OLED panel and... -
I have a post on psx-place for this but thought I'd try here as well in case anyone has experience or the schematics or any kind of help. Here's the original post from psx-place:
START
Hi, so I bought a YLOD Fat PS3 as I wanted a repair project and thought it would be a good way to get experience. I was able to solder to the RX, TX and Diag pads on the COK-002 motherboard and was able to get external access and retrieved the codes. I haven't powered it on beforehand so these should be the last ones. I did try to get internal access immediately after but kept getting scopen response...
Comment