Hi I have a philips 42PFP5532D which is stuck on standby and the power LED flashes 1 long flash then 4 short ones, then 1 long and 5 short, then 1 long and 2 short? Does anyone know the problem? Does anyone know any blinking codes for TVs??
-
-
Re: philips 42PFP5532D stuck on standby
What's the chassis code - printed on rear of set for example Q599.3E-LA? Next to normal model number.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search. -
Re: philips 42PFP5532D stuck on standby
Hi tom66 Where would I find the Chassis code? I have the serial and model number but nothing saying the Chassis codeComment
-
Re: philips 42PFP5532D stuck on standby
Can you provide a picture of the back model number label?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: philips 42PFP5532D stuck on standby
Hope this helpsAttached FilesComment
-
-
Re: philips 42PFP5532D stuck on standby
not sure if tom has this but im sure this is the correct link
Comment
-
Re: philips 42PFP5532D stuck on standby
Yes chassis is LC7.2E-PA.
So this is a plasma?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: philips 42PFP5532D stuck on standby
Yeah it isComment
-
Re: philips 42PFP5532D stuck on standby
Here's exact manual
Error codes page 18.
error code 4: General I2C error
error code 5: Trident video processor error
error code 2: +12V low/missing
I'd focus on error code 2. It looks like it could cause the other two errors. Check +12V at PSU.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: philips 42PFP5532D stuck on standby
IS this toms-service-manual your website? Can I just generally browse through it for other TVs?Comment
-
Re: philips 42PFP5532D stuck on standby
Yes, and yes.
http://www.toms-service-manuals.com/
http://www.tgohome.com/ServiceManuals/Last edited by tom66; 03-04-2014, 12:50 PM.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: philips 42PFP5532D stuck on standby
Cheers top lad!Comment
-
Re: philips 42PFP5532D stuck on standby
Well with most likely it being the +12V protection error code is that a fault on the power supply board? Is it a certain component or just a whole board change?Comment
-
Re: philips 42PFP5532D stuck on standby
It probably indicates a fault with the 12V out of the power board, but there's also the chance the main board is shorted. Also possible the main board is mis-detecting the fault and there actually isn't one (I've had this before.)
To find exact fault, it's best to check the 12V from the power supply just as the set is turned on. If it's low, then that points to a fault in the first two categories. If not, it's in the latter category.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Hello, guys!
The same 32" Philips TV I was having video issues, but now I don't have standby led at all. Someone here shared with me the schematic of the power supply, and checking the voltages, I see right after the resistor R604 I'm getting 1.6 v which is too low for enabling the Gate of the Q601 mosfet (the diagram says 4.2). On the R614 resistor I'm getting 181 V in and 117 V out, then through R603 I'm getting the same 117 V in and 59.9 V out, finally getting the latter voltage in the R604 BUT getting just 1.6 V out, which is the voltage that goes on to the Gate of the Q601... -
Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.
It does power up when pressing the power button.
I already try the power button while plugin the plug with no result.
Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.
Could this be an PSU or eMMC issue ? -
Hello
I have an TV Led 4K Selecline 65s18 with mainboard T.MS3458.U801
The TV is faulty with stuck in Standby RED LED. Can't power the TV.
Before this problem , the TV stuck the picture with artefact , i unplug the AC cable and since the tv is stuck in standby .
All voltage are OK on PSU and main board for regulator. I tried flash firmware 25Q64 with many dumps
But the voltage on power button is 0.6V not 3.3V. When i press power button the voltage up to 0V. I tried to add 5V with Power Supply on 5V_STB and 3.3V on Power... -
Hello,
I have a problem with this TV, the standby voltage is not present. I have checked the components around the IC fsq510's area and they seem to work, also replaced this IC but the problem persists.
These are the voltages in some pins of IC fsq510:
Vcc=18v
D=320v
Vstr=154v
Unfortunately, I couldn't find the schematic
What else could I check?
Is it possible to provide standby voltage from an external source to allow the TV to turn on?
Thank you​... -
Hello to all friends of the forum and well found, here I am asking for your help and sorry for my translated English.
As per Hisense tv title LTDN50K220WSEU stuck in standby
PSU rsag.820.5687 HLL 4855WF
Main rsag 7.820.5842
I enclose the psu diagram, after the first routine checks I find myself with a regular standby voltage of 3.3v blue light on steady when the power button is pressed nothing happens, psu disassembled and bench checked ... forced ignition by sending a signal 3 , 3v on the SW and PWM2 pins the psu turns on and delivers all the voltages...
Comment