Dead Sanyo DP26648 logic board, need service manual.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Spork Schivago
    Badcaps Legend
    • Mar 2012
    • 4734
    • United States of America

    #21
    Re: Dead Sanyo DP26648 logic board, need service manual.

    Originally posted by cashkennedy
    Part number on the main board is 1LG4B10Y02200. So looks like you might be in luck if you need any parts from it.

    I attached pics to show what all i have, though theres speakers, and cables that arent shown.
    By any chance do you still have the cable that goes from the logic board to the T-CON board? I tripped over the cord that plugs the TV into the outlet and did a bit of damage.

    The connector on the T-CON board lifted a bit off the board. I tried soldering it back down. I didn't get it perfect but it's holding it down a little. Just at a slight angle.

    I'm getting absolutely nothing on that VIN_12V on the T-CON board now and on the cable on the T-CON side, a wire isn't staying in the connector because I broke the little thing that prevents the wire from coming out off.

    Just more bad luck I guess. I don't know if I jacked up some of the T-CON board pins when I tripped over it and that's why there's no voltage at all on the test point or if it's because of the wire on the cable. I doubt it's the wire though because it's the second to the last on the opposite side of the VIN_12V test point.

    {: - (
    -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

    Comment

    • cashkennedy
      Badcaps Veteran
      • Aug 2011
      • 666
      • USA

      #22
      Re: Dead Sanyo DP26648 logic board, need service manual.

      I do have the lvds cable, but i would try fixing your connections first, cause i doubt the cable is the issue. But you might be able to use electrical tape to get the connector to stay in. and then use a low ohm setting to make sure the pins on eahc side are connected (perferably test from the traces before the connectors so you know you resoldered all the pins fine in the connector.
      Fixed so far 12 lcd's , 1 plasmas, 5 monitors, 0 dlp's (plan to keep the dlps at 0). and 3 atx power supplies, and 2 motherboards.

      Comment

      • Spork Schivago
        Badcaps Legend
        • Mar 2012
        • 4734
        • United States of America

        #23
        Re: Dead Sanyo DP26648 logic board, need service manual.

        Yeah, I'm thinking maybe the connector is fine now. I mean there's two wires that aren't securely in but I was thinking of maybe just gluing them down or something. I'm also thinking because of Q6360 being shorted by me on pins 4 and 5, maybe that's why I'm not getting any voltages on VIN_12V. I'm home now and I'm going to try the 1-2 watt resistor idea. Wish me luck!
        -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

        Comment

        • Spork Schivago
          Badcaps Legend
          • Mar 2012
          • 4734
          • United States of America

          #24
          Re: Dead Sanyo DP26648 logic board, need service manual.

          Originally posted by budm
          That MOSFET pin out, PIN 1, 2, 5, or 6 are tied together and is the output. Pin 4 is an input. I avoid using the term SOURCE, GATE, DRAIN to be less confuse. So jump Pin 4 to anyone of the pin 1, 2, 5, or 6, then you will have 12vdc on the T-CON board and you shoulde see pictures.
          Pin 3 is the contol pin that turns the MOSFET on/off. 8VDC should be there when the TV is ON, and about 0V when TV is OFF.
          Hmm, I haven't soldered the resistor yet but because pin 3 is now reading some wheres around 0vdc when the TV is on, does that mean I messed something up and this won't work? All I did was touch pin 4 and 5 at the same time. From what you've said, I don't see how that could of done anything. Pin 3 was reading around 8vdc. After I touched 4 and 5, it sparked a little. Then I went to pin 3 and it was reading 6vdc and just kept going down.

          I'll still solder the resistor I guess and hope for the best. Also though, because something is physically wrong with the MOSFET, would those various pins still be tied together? Or is there a chance some of the traces inside the chip burned to the point where they're no longer tied?
          -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

          Comment

          • Spork Schivago
            Badcaps Legend
            • Mar 2012
            • 4734
            • United States of America

            #25
            Re: Dead Sanyo DP26648 logic board, need service manual.

            Something went TERRIBLE!!! wrong. I successfully soldered pins 4 and 6 together on Q6360. When I plugged it in and turned the TV on, I smelled something. I looked down and the chip was smoking. Lots of smoke coming from it and everything. It appeared to be coming from that chip but it's hard to say for certain because I unplugged it before I took a closer look. Any ideas on what went wrong?
            -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

            Comment

            • budm
              Badcaps Legend
              • Feb 2010
              • 40746
              • USA

              #26
              Re: Dead Sanyo DP26648 logic board, need service manual.

              I would remove that IC, I cannot see why it will smoke since none of the pins are connected to ground, for it to smoke, a lot of current has to complete the circuits back to ground, please remove the IC, remove the damaged LVDS cable, clean the board and inspect the board real close to see if any one of the pin is connected to the ground plain. That MOSFET is nothing but a electronic switch, current goes into pin 4 and flow out to pin 1,2, 5, and 6 and out to the T-CON board. Please recheck your solder works. put the jumper back on pin 4 and 6 and you should read 12v on those pins.
              Never stop learning
              Basic LCD TV and Monitor troubleshooting guides.
              http://www.badcaps.net/forum/showthr...956#post305956

              Voltage Regulator (LDO) testing:
              http://www.badcaps.net/forum/showthr...999#post300999

              Inverter testing using old CFL:
              http://www.badcaps.net/forum/showthr...er+testing+cfl

              Tear down pictures : Hit the ">" Show Albums and stories" on the left side
              http://s807.photobucket.com/user/budm/library/

              TV Factory reset codes listing:
              http://www.badcaps.net/forum/showthread.php?t=24809

              Comment

              • cashkennedy
                Badcaps Veteran
                • Aug 2011
                • 666
                • USA

                #27
                Re: Dead Sanyo DP26648 logic board, need service manual.

                Yeah its surprising that it didnt work. Perhaps you have a lot of solder on 4 and 6 and so it flowed to the ground, or maybe yoru testing the board whil ites not screwed down in its proper place so something on the board touched ground.

                Also, you probably know this, but pins are numbered counter clockwise from the notch / dot. so the nearest pin to the notch / dot is 1.
                Fixed so far 12 lcd's , 1 plasmas, 5 monitors, 0 dlp's (plan to keep the dlps at 0). and 3 atx power supplies, and 2 motherboards.

                Comment

                • budm
                  Badcaps Legend
                  • Feb 2010
                  • 40746
                  • USA

                  #28
                  Re: Dead Sanyo DP26648 logic board, need service manual.

                  I have a feeling he shorted the trace to ground plain some how, that is the only explanation.
                  Never stop learning
                  Basic LCD TV and Monitor troubleshooting guides.
                  http://www.badcaps.net/forum/showthr...956#post305956

                  Voltage Regulator (LDO) testing:
                  http://www.badcaps.net/forum/showthr...999#post300999

                  Inverter testing using old CFL:
                  http://www.badcaps.net/forum/showthr...er+testing+cfl

                  Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                  http://s807.photobucket.com/user/budm/library/

                  TV Factory reset codes listing:
                  http://www.badcaps.net/forum/showthread.php?t=24809

                  Comment

                  • Spork Schivago
                    Badcaps Legend
                    • Mar 2012
                    • 4734
                    • United States of America

                    #29
                    Re: Dead Sanyo DP26648 logic board, need service manual.

                    Originally posted by budm
                    I have a feeling he shorted the trace to ground plain some how, that is the only explanation.
                    I know my solder isn't touching the ground plane at all. I will remove the IC and resolder my resistor to pin 4 and 6. The board is not screwed down, however, it's on a cardboard box and nothing is grounding out.

                    Before the resistor was put in place, I tested it after repairing the cable the best I could and there was no smoke. I believe the cable is working fine. I will go over what you guys suggested though.

                    I was thinking. Could this be why the chip was all burned out? Maybe it wasn't something I did but perhaps something that failed in the circuit and caused this to burn out? Maybe a diode or something? Just a thought. Remember, when I accidently touched pins 4 and 5, it sparked and then pin 3 lost all it's voltage.
                    -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                    Comment

                    • Spork Schivago
                      Badcaps Legend
                      • Mar 2012
                      • 4734
                      • United States of America

                      #30
                      Re: Dead Sanyo DP26648 logic board, need service manual.

                      Originally posted by cashkennedy
                      Yeah its surprising that it didnt work. Perhaps you have a lot of solder on 4 and 6 and so it flowed to the ground, or maybe yoru testing the board whil ites not screwed down in its proper place so something on the board touched ground.

                      Also, you probably know this, but pins are numbered counter clockwise from the notch / dot. so the nearest pin to the notch / dot is 1.
                      I will double check, but the amount of solder I used is very minimal and I always go over my work with a magnifying glass.

                      The pin numbers for the IC are labeled on the board. So I'm certain I have the correct order. I'm always worried about having the wrong pins so I'm extra careful about that. I think it's from me killing so many transistors when I was younger trying to test them.
                      -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                      Comment

                      • cashkennedy
                        Badcaps Veteran
                        • Aug 2011
                        • 666
                        • USA

                        #31
                        Re: Dead Sanyo DP26648 logic board, need service manual.

                        Yeah its possible you didnt make any of those simple error, cause it sounds like you were making sure not to do anything stupid.

                        Good luck with removing and bypassing it.
                        Fixed so far 12 lcd's , 1 plasmas, 5 monitors, 0 dlp's (plan to keep the dlps at 0). and 3 atx power supplies, and 2 motherboards.

                        Comment

                        • Spork Schivago
                          Badcaps Legend
                          • Mar 2012
                          • 4734
                          • United States of America

                          #32
                          Re: Dead Sanyo DP26648 logic board, need service manual.

                          I hope I didn't. I didn't have time to remove it last night and today we have to go to my girl's mum's house for dinner. When I get back, I'll give it a shot. I found out what was smoking. It was the resistor. The 1 ohm 1/4watt resistor I used is all burnt and crispy.

                          It's still a very real possibility that I did something earlier on to cause this. Before I soldered the resistor on. It wouldn't be the first time I made a simple stupid error. Won't be the last either!

                          Anyway, I gotta take off now. Just wanted to give every ones the heads up.
                          -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                          Comment

                          • Spork Schivago
                            Badcaps Legend
                            • Mar 2012
                            • 4734
                            • United States of America

                            #33
                            Re: Dead Sanyo DP26648 logic board, need service manual.

                            I removed the IC. I had only soldered where that chip was, however, I went over everything with a fine tooth comb. Nothing looks out of the ordinary. I have successfully soldered a resistor to pin 1 and pin 4 at where the IC used to be. I am going to try again. All I can think is you must of been right and some how when I soldered my resistor last time, it reached ground. I looked it over so well though.
                            -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                            Comment

                            • Spork Schivago
                              Badcaps Legend
                              • Mar 2012
                              • 4734
                              • United States of America

                              #34
                              Re: Dead Sanyo DP26648 logic board, need service manual.

                              Well, this thing is a lost. The board caught fire. Hrrrmmmm. At least the resistor didn't burn up this time.
                              -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                              Comment

                              • Spork Schivago
                                Badcaps Legend
                                • Mar 2012
                                • 4734
                                • United States of America

                                #35
                                Re: Dead Sanyo DP26648 logic board, need service manual.

                                Originally posted by budm
                                please remove the IC, remove the damaged LVDS cable, clean the board...
                                I'm such a stupid idiot. I can't believe I left that damn LVDS cable in. I was so excited, got it all hooked up and everything. When I finished soldering, I just hooked all the cables up like I normally do. I didn't even think about it. This is going to cost me a ton to fix now. I'm going to try to get that logic board off Cashkennedy and replace the T-CON board and T-CON cable as well. It had to be something with that LVDS cable or the connector. Just more bad luck I guess.
                                -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                                Comment

                                • Spork Schivago
                                  Badcaps Legend
                                  • Mar 2012
                                  • 4734
                                  • United States of America

                                  #36
                                  Re: Dead Sanyo DP26648 logic board, need service manual.

                                  Originally posted by cashkennedy
                                  Yeah its possible you didnt make any of those simple error, cause it sounds like you were making sure not to do anything stupid.

                                  Good luck with removing and bypassing it.
                                  Do you still want to sell me that LVDS cable and Logic Board? If so, how much do you want? I will pay you what you think it's worth. Don't give me a good price because of my luck or anything. Charge me what you think is fair. That is, if you're still willing to sell it.
                                  -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                                  Comment

                                  • cashkennedy
                                    Badcaps Veteran
                                    • Aug 2011
                                    • 666
                                    • USA

                                    #37
                                    Re: Dead Sanyo DP26648 logic board, need service manual.

                                    I think 30 is a good price that youd see on ebay if you waited a while for a good deal. But id be glad to get anything over 20.

                                    You can PM me your address, and ill pm you my paypal email.
                                    Fixed so far 12 lcd's , 1 plasmas, 5 monitors, 0 dlp's (plan to keep the dlps at 0). and 3 atx power supplies, and 2 motherboards.

                                    Comment

                                    • Spork Schivago
                                      Badcaps Legend
                                      • Mar 2012
                                      • 4734
                                      • United States of America

                                      #38
                                      Re: Dead Sanyo DP26648 logic board, need service manual.

                                      Originally posted by cashkennedy
                                      I think 30 is a good price that youd see on ebay if you waited a while for a good deal. But id be glad to get anything over 20.

                                      You can PM me your address, and ill pm you my paypal email.
                                      Okay, give me a couple days to get the cash and then I will PM you with all of my information. Then maybe you can give me a total for it (shipping + the product). Thanks.

                                      -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                                      Comment

                                      • cashkennedy
                                        Badcaps Veteran
                                        • Aug 2011
                                        • 666
                                        • USA

                                        #39
                                        Re: Dead Sanyo DP26648 logic board, need service manual.

                                        No problem, just email me at the paypal email, if im too busy to check the forum daily.
                                        Fixed so far 12 lcd's , 1 plasmas, 5 monitors, 0 dlp's (plan to keep the dlps at 0). and 3 atx power supplies, and 2 motherboards.

                                        Comment

                                        • Spork Schivago
                                          Badcaps Legend
                                          • Mar 2012
                                          • 4734
                                          • United States of America

                                          #40
                                          Re: Dead Sanyo DP26648 logic board, need service manual.

                                          Originally posted by cashkennedy
                                          No problem, just email me at the paypal email, if im too busy to check the forum daily.
                                          Okay, I got the money. I will try sending you a PM. Not too sure on how to do it so if it doesn't come in, I will e-mail you at the address you gave me for paypal.
                                          -- Law of Expanding Memory: Applications Will Also Expand Until RAM Is Full

                                          Comment

                                          Related Topics

                                          Collapse

                                          • yuuki47
                                            A2681 M2 MacBook Air Dead Logic Board
                                            by yuuki47
                                            Hello...

                                            My sister purchased an M2 MacBook Air a year and a half ago. While she was using it a week ago, it randomly shut off and no longer powers on. There are no signs of life and not even the MagSafe indicator LED lights up.

                                            We took it to Apple and they disconnected the battery and tried a bunch of stuff before they declared the logic board "brain dead" and quoted us about £567 to replace it. Typical of them...

                                            eBay replacements run about £367 with the Touch ID sensor included.

                                            I did consider to probe the logic board for shorts...
                                            04-13-2024, 06:22 AM
                                          • double_DD
                                            How can I be sure that my EC chip is dead?
                                            by double_DD
                                            Hi all,

                                            As the title suggests, how can I be sure that my EC chip is really dead?

                                            I've recently gotten into this hobby of laptop repairs, and have successfully brought back to life a couple with some easy fixes, mostly shorted caps.

                                            Now I'm working on HP Probook 455 G8, that had some "devil" run around on 3V line, burning a bunch of stuff. Luckily I have a dead 455G7 (for spare parts) so I managed to fix it (swapped burned parts) to a point that it will charge (both on barrel jack and usb-c), but it doesn't want to turn on. There is a 3V3 on a keyboard...
                                            03-12-2025, 07:47 AM
                                          • ohren
                                            Upgrading a Samsung ue55nu7096u with logic board from an ue55ru7105k -- good idea?
                                            by ohren
                                            I hope this is the right forum to post in despite not technically being a repair, but still a question of swapping boards.

                                            I thought I'd explore the possibility to upgrade an existing working Samsung ue55nu7096u with the logic board (and power board if needed) of a newer model (ue55ru7105k) of the same size and appearance (and resolution). The reason being I'd like the extra inputs of that board including component in, an extra HDMI port and bluetooth. Its panel is broken so I have no use for the board otherwise.

                                            The models launched in 2018 and 2019 respectively....
                                            09-08-2023, 05:24 PM
                                          • korben_dallas
                                            Will I have a bricked logic board after reflow of the GPU v-core U8900 chip on my Mid-2012 15" Retina Macbook pro?
                                            by korben_dallas
                                            Hi everyone! I'm trying to fix my black screen / failed U8900 GPU v-core on my Mid-2012 Macbook Pro 15" Retinaby doing a rework/reflow of the chip (once I determine that's the real issue; but it likely is).

                                            I've been disabling the GPU in NVRAM for a few years... but it's just time for a better solution.

                                            I'm new to soldering but the only feasible way to fix this issue is to do something myself.

                                            MY QUESTION:
                                            I've been seeing some people (on this forum mostly) run into issues with the logic board needing a serial number or it being deactivated (?)...
                                            02-14-2024, 12:23 AM
                                          • disorder
                                            ps5 edm-033 dead after hdmi/usb ports destroyed
                                            by disorder
                                            hello guys,

                                            i need help to repair a edm-033 ps2
                                            history : as always hdmi port and usb ports destroyed after unplugged
                                            after change them, ps5 dead too : 1 beep, no blue light. after inspection 1.8v power was shorted, and because of dead panasonic chip. after remove it : no short anymore
                                            so i changed it
                                            now i have got 5v stby,, 3.3v stby, 3.3v power, 1.8v power and no short on them
                                            but the ps5 is dead again : 1 beep, near 10 seconds with power lines and then off, no blue light ...

                                            i don't see any projection of liquid metal on pcb.
                                            ...
                                            01-14-2025, 12:48 PM
                                          • Loading...
                                          • No more items.
                                          Working...