Burn-in test duration for LCD monitors and LCD TV's

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Dgtech
    E. Technician
    • Apr 2009
    • 1462
    • Steeler
    #1

    Burn-in test duration for LCD monitors and LCD TV's

    I have question to my fellow tech's. How much time do you guys think is adequate for running a set (for test) after fixing it and before selling it? I'm sure these answers will vary between techs and probably between TV's and monitors. Just curious what answers will come back.
    The strong-minded rise to the challenge of their goals,the weak-minded BECOME HATERS

    Tags: None
    • Per Hansson
      Super Moderator
      • Jul 2005
      • 5895
      • Sweden
      #2
      Re: Burn-in test duration for LCD monitors and LCD TV's

      Depends on the problem
      If a dead set and you bring it back to life obviously you found the issue so 99% it will be fine, so no more testing needed really
      If intermittent problems it will be up to the case, how (if at all) is the problem possible to reproduce etc
      "The one who says it cannot be done should never interrupt the one who is doing it."

        Comment

        • ecking767
          Badcaps Veteran
          • Oct 2009
          • 492
          • USA
          #3
          Re: Burn-in test duration for LCD monitors and LCD TV's

          I test LCD TV and LCD monitors for a week or sometime more before selling it. 8 hours a day or more.

            Comment

            • severach
              Badcaps Legend
              • Aug 2007
              • 1055
              • USA
              #4
              Re: Burn-in test duration for LCD monitors and LCD TV's

              I plop the fixed monitor on a nearby desk and sell the one that was there working fine.
              sig files are for morons

                Comment

                Previous template Next

                Related Topics

                Collapse
                • chth96
                  How Can I test PWM DM0365R?
                  by chth96
                  Hello
                  I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
                  So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
                  I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
                  I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
                  06-18-2025, 04:14 PM
                • khelane
                  test active pfc power with lamp test
                  by khelane
                  Hello
                  I have a big problem and that is that in some cases when repairing active pfc power supplies I cannot work with a test lamp. I can only get help with 5 volts standby and for starting and starting I have to work without a lamp and this way there is a possibility of parts exploding and other parts being added.
                  Sometimes with a multimeter test the problems can be reduced to some extent, but I had several cases that had to be tested on and online and recently two varistors exploded. They had terrible resistance because the power supplies were over 800 watts.
                  Is there a way...
                  06-03-2025, 01:00 AM
                • chronic519
                  Mats / mods: detected and repaired GPU fault. Cant seem to test after!
                  by chronic519
                  Hello.

                  GPU came in, green lines. Spent lots of time using to get the Mats / mods drive working (found on youtube).
                  Found issue with a RAM block
                  Replaced, green lines gone.
                  Trying to test again, assuming getting the false positive. Originally had over 1K on a single bank. Now getting tosses low between banks.
                  Used a good card to test and same results low errors 32+.

                  I am just search for some form of command to do a full test on the GPU.
                  I just ran the mats command with my good GPU and passed after roughly 40 min.
                  The repaired one, ran...
                  05-20-2025, 07:56 PM
                • hemant_2222
                  Yamaha 2064 No sound but Test audio working
                  by hemant_2222
                  Hello Guys,

                  Greetings!

                  Hope you all are doing well.

                  I am looking for suggestion on Yamaha 2064. The problem with this receiver is that it has no sound however when the test tones are activated it does outputs from all the speakers. It is working in two channel stereo mode but when you select other sound modes, it doesn't. The last time it had a problem, I had replaced the DAC
                  PCM1681DBQR - IC263 and it worked fine.

                  Other issue with it is one of the STK ICs is getting more heated then the other one but that can be looked at later.
                  ...
                  11-01-2025, 11:20 PM
                • alltvrepairs
                  Lg TCon test pins for screen test
                  by alltvrepairs
                  Hi,
                  i have a 65 Panasonic TX-65HX710E using vestel 17MB170 main and Lg tcon.

                  Few drops of water fell probably near COF and have no display. Tried removing tabs but no.part of display present as if tcon fuse open. However 12v is present and tcon can be felt warm enough that supplies are present. Backlight and sound ok.

                  Anyone knows if this TCon 6870c-0805A has any special test pins for rgb test?

                  Appreciate your help....
                  2 Photos
                  06-13-2025, 06:33 AM
                • Loading...
                • No more items.
                Working...