Re: Help with Cannon iP4850 Printer
Yes try a dummy run without power to the board
Yes try a dummy run without power to the board
-
Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740 -
Re: Help with Cannon iP4850 Printer
I did it,
Dummy run -003
Power on -330Last edited by SmartestSmarty; 07-21-2014, 04:14 AM.Comment
-
Re: Help with Cannon iP4850 Printer
Good or bad?Comment
-
Re: Help with Cannon iP4850 Printer
Good effort - Now move to the socket at the other end of the board.
Same safety conditions apply though tests on lower voltages
Set your meter on vDC200 I cant see any pin marks unless one is a minus sign.
Basically you need to find which is ground ( May well be the one with the minus on)
see if anything goes from there to the negative side of those smaller caps?
No Power to board while your searching.
Then having established ground (switch power back on) put black probe on ground and test each pin on the socket with the red probe.Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: Help with Cannon iP4850 Printer
Heres a pic of the other side of the board. I'm not sure which would be ground?
On the actual connecter, the connection to the pin which says 1, on the connecter says H JST. The second connector says F2. There is also a little x in-between both of these connection points.
The third says 3, the fourth says 4 and the fifth says 5.
Does this help?Attached FilesLast edited by SmartestSmarty; 07-21-2014, 04:44 AM.Comment
-
-
Re: Help with Cannon iP4850 Printer
Do I need to use V Flat Line, three dots 200?Comment
-
Re: Help with Cannon iP4850 Printer
Do I need to use V Flat Line, three dots 200? Yes
See pic think second pin is the ground. Just check that the joints marked C-
line up with the white stripe on the side of the capsAttached FilesPlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
-
Re: Help with Cannon iP4850 Printer
Small red Cs in my picture - must get fonts fixed that is the only size ive gotPlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Please upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: Help with Cannon iP4850 Printer
Sorry just seen your picture, yes they line up.
I'll test it like this.
Negative probe on second pin, carefully touch red probe on other pins.Last edited by SmartestSmarty; 07-21-2014, 05:19 AM.Comment
-
Re: Help with Cannon iP4850 Printer
Results.
2nd (ground) and 1st: 0.00
2nd (ground) and 3rd: 08.6
2nd (ground) and 4th: 0.00
2nd (ground) and 5th: 11.2Last edited by SmartestSmarty; 07-21-2014, 05:38 AM.Comment
-
Re: Help with Cannon iP4850 Printer
Once its switched off, do I need to touch the long nose pliers to the big cap soldering points. This drains the excess current or something doesn't it?Comment
-
Re: Help with Cannon iP4850 Printer
I guess you've gone offline now
Comment
-
Re: Help with Cannon iP4850 Printer
no, if you do that you get a big bang and damage both the cap and the end of the pliers.
if you leave it a while it should discharge - you can test it later wih the meter to see if it's dropped.
when you do, you set the meter to dc and atleast 400vLast edited by stj; 07-21-2014, 06:03 AM.Comment
-
Re: Help with Cannon iP4850 Printer
OK thanks.
I'm not sure if you read the whole thread, but i've done the last test, just not sure if the results are good or bad, and what to do next?Comment
-
Re: Help with Cannon iP4850 Printer
and post a foto that shows ALL of the bottom of the board!Comment
-
Re: Help with Cannon iP4850 Printer
i skimmed over it,
if i could see all the underside of the board i'd know how the connector links up.
but i think it's o.k. or atleast it's not dead.
(obviously)Comment
-
Re: Help with Cannon iP4850 Printer
just getting a sandwich but i do have to go out.
I think that part is functioning ok but without a service manual or previous experience of printer voltages cant be surePlease upload pictures using attachment function when ask for help on the repair
http://www.badcaps.net/forum/showthread.php?t=39740Comment
-
Re: Help with Cannon iP4850 Printer
So basically there's nothing wrong with the power board?
What else would stop the printer not turning on?
Here's a complete pic of the power board:Attached FilesComment
-
-
TE Circuit Protection offers the widest selection of surface-mount fuses available for addressing a broad range of overcurrent protection applications. Helping to prevent costly damage and promote a safe environment for electronic and electrical equipment, our single-use chip fuses provide performance stability to support applications with current ratings from .5A up to 20A.
TE Circuit Protection also offers the telecom FT600 fuse for telecommunications applications. This telecom fuse helps comply with North American overcurrent protection requirements, including Telcordia, GR-1089,...10-07-2024, 06:07 AM -
I was working on this machine yesterday and I now going to use an incandescent lights instead of a fuses to figure out what the issue is with it blowing control voltage rail but this not the only issue the coolant pump failed the meager test as well as the main motor as well this motor has 12 motor wire leads instead of the normal 9 wires
This metal lathe has a weird motor setup it has a soft start motor with a “Y” and a delta type of motor winding setup and it is not done in the motor pucker head enclosure it is with four different contactors wired in a configuration I have not... -
Hello all, as the title says, I'm very much in need of a valid firmware dump of a Anycubic Photon 5.5 3D resin printer. It's stored in a Winbond 25Q32, so it's 4Mbyte.
Here's a little background for my request. A few weeks ago I bought this 3D printer from a guy who had moved on to a PLA printer. I got it at a vey reasonable price, as it was in a defective state. The seller told me that he had experienced a power failure during a firmware upgrade, after which the printer appeared to be dead. He thought the firmware was corrupted in such a way that the printer was now bricked. As he... -
SOLVED. I removed the printer in settings, replugged and let it reinstall and it worked this time.
Brother HL-2140 laser printer
Windows 10
Attempt to print and immediately get a Windows pop-up saying "Error printing". The document appears in the printer queue window with Status "Error-printing".
Turned off printer. Unplugged, waited, replugged. Ran the Windows troubleshooter. Removed and reinserted toner cartridge. Checked for paper jam. No printer error lights. Reinstalled driver. Restarted the Spooler service. Rebooted...06-22-2023, 11:11 PM -
Hello
I have power adaptor(220V/input, 12V 1.2A/output) which has symptom of fluctuating output DC voltage between 11.5V-12.2V.
So I opened its plastic case and when switched it on, I heard constant tik tik sound from inside its PCB.
I measured DC voltage between negative and positive pin of the largest capacitor(400v 10uf) and it was measured contant 300V.
I also measured ESR value of all capacitors and I noticed that one of capacitor(KMG 16v 470uf), which located in the secondary side, have high ESR value(10 ohm),So I replaced it with same specification NXH capacitor....
Comment