-
@volinakis hi bro please im again i need this region CLEAN RGN STOCK production= PMC= JSP_135.3.00.1036_N_A_PRD,bin
-
thanks so much broLast edited by leo037_2023; 11-26-2023, 05:49 PM. -
you can take ME firmwares from
https://mega.nz/folder/2Q0klQpA#6o04nlV_4xqfx76tjvgi4gLeave a comment:
-
hi everyone i try to find a REGION ME CS ME 13.50.22.1735 (RGN STOCK)
if someone has this region RGN STOCK, could you upload it and share it
Attached FilesLeave a comment:
-
-
Re: ME Firmware Cleaning Guide
I have a question. I fix Dell Inspiron 15 5510 , then clear me bios. but ssd not show in bios setup. Can you teach me to fix it?Leave a comment:
-
-
-
Re: ME Firmware Cleaning Guide
Hey, where can i upload this file? This TXE firmware is not in the databaseAttached FilesLeave a comment:
-
-
Re: ME Firmware Cleaning Guide
Here is the archive with bunch of CSME System Tools v16.1 r0
Flash Programming Tool
FWUpdate
Manifest Extension Utility
MEInfo
MEManuf
Modular Flash Image ToolLeave a comment:
-
-
Re: ME Firmware Cleaning Guide
I checked my BIOS dump with ME analyzer, which is 9.1.37.1002.
I use Intel ME System Tools v9.1 r7 package and FIT, but no matter what I do I will always get an error when opening the BIOS dump in FIT. No idea what I could be doing wrong. Error number 22.
Attached FilesLeave a comment:
-
-
Re: ME Firmware Cleaning Guide
CSME System Tools v16.1 r0-1
Enjoy.Leave a comment:
-
-
-
-
Re: ME Firmware Cleaning Guide
Hi brother, please give me knowledge
On CSME 14 I did not find the ME Region.bin file in the Decomp folder as mentioned in point 5.
I usually clean ME by replacing the ME file via the menu in FIT, namely "Intel(R) ME Binary File".
Is the method I usually do correct or not?Leave a comment:
-
-
If you have to clean the ME firmware on **some microsoft surface models the touchscreen can stop working.
** Some models do not need this fix.
*You should install the latest updates from microsoft,including the driver packs before assuming there is a hardware problem.* - See Post #2
EDIT: If nothing else works try this fix - https://www.badcaps.net/forum/showpo...8&postcount=40
Always check a working dump from the same model using FIT.If the working dump default setting for "Integrated Sensor Hub Supported" is set to "NO"... -
i know a tool https://github.com/MuertoGB/MacEfiToolkit is capable of SN change and Clean ME but not updating EFI Version of the BIN file. is there a guide or a BIOS structure to update the firmware??...03-06-2024, 01:34 AM -
Hello to everyone ,
This is my first post here, and i would like to share with you a small story in case you can help me.
Docker Type-C Gen 2 - Model 40AS. Was given to me by a friend for free ,but with the problem that you cannot use the video output ports.
All ports work , USB , Ethernet, Type C ... but HDMI + Display Port don't work
I searched on reddit and google for problem similar to that, and a LOT of people had fixed this problem by updating the firmware. So i tried , i searched and found 1.1.13 utility and 1.1.20 utility that can help...02-10-2024, 02:07 PM -
Hi guys.
I've got a Ubiquiti US-8-150W POE switch which has issues with updating the firmware.
Turned out to be a bad EEPROM chip. It would read the firmware and work as normal, but failed to write new firmware to it.
So I took off the chip and read on EEPROM and saved it. Wrote to old chip and failed to write
Got New chip and writes good.
THE PROBLEM...
It fails to fully load the firmware, POE lights fail to work during g firmware test during load. I'm suspecting bad EEPROM Read.
Does anyone have a Good Firmware I can have?... -
Hello Badcaps Community,
I purchased a preowned AOC monitor that is not working and out of warranty. It was sold as not working. I am looking for guidance on self-repair. In particular, I am after the firmware for the monitor. At the end, I have included monitor model information and links to pics and vids of the issue.
The problem is that it will not display a picture on any of its inputs. And the on-screen menu does not appear. The power button works properly. It powers on with the remote as well. But the on-screen menu does not appear, even when not connected to any...
Leave a comment: