"exact model" and serial number have to be written in request, read RULES.
https://www.badcaps.net/forum/troubl...sting?t=103570
-
Does anyone know how to clean this ME region and extract EC bin from these binaries? It is an MSI (exact model in the binary name)Leave a comment:
-
-
-
I was struggling to find on internet ME Fw 16.1 27.2225 Corporate LP ADP A for HP 640 G10 and I had the idea to use MFIT 16.1 to extract ME Firmware from update package and ... it works!
What I did:
1. Downloaded bios update from HP that corresponds with my bios version (V75 01.02.03)
2. unpack bios update and there is a bin file , in my case V75_01020300.bin
3. Decompose V75_01020300.bin with MFIT 16.1
4. Hit "Build" tab. MFIT will create image "FWUpdate.bin"
Leave a comment:
-
hi everybody !
please provide Flash Image Tool 18.0.5.2077 ?
Thanks!Leave a comment:
-
-
-
Hi, can anyone please provide Flash Image Tool 16.1.27.2236?
Thank you!
Leave a comment:
-
-
Hi, im getting errors with V15 IFIT. I've tried few versions, can someone help ?Attached FilesLeave a comment:
-
-
ineed Intel Management Engine 11.8 Firmware version 11.8.93.4323
thinksLeave a comment:
-
Could anyone tell me what's wrong? I tried 0, 3, 4, 5 and still can't create the image.
Thanks
Attached FilesLeave a comment:
-
-
Post your request here --> https://www.badcaps.net/forum/troubl...matic-requests .Include the make and model in your thread title.Include the PC serial number in your post. Read the rules please https://www.badcaps.net/forum/troubl...before-postingLeave a comment:
-
I've cleaned my ME as described and I am wondering if I did it right.
Before cleaning: ME Analyzer shows Chipset as SPT-H D
After cleaning KBP/BSF/GCF-H A SPT-H D
Is that an expected output or did I screw something up?
TLDR:
Replaced HP ZBook 17 G3 motherboard (new), added SN/Model/Board/Build/Featurebyte, locked MPM and ended up with "Warning...not in commited state". I believe I forgot to make some ME settings.
Upgraded BIOS and ME firmware to latest version. Then I dumped the BIOS with a programmer and cleaned ME using firmware ME_11.8_Corporate_D0_H_Production.bin. Warning message is gone, laptop runs fine. How do I check if everything REALLY is fine?! 😅
Leave a comment:
-
If you have to clean the ME firmware on **some microsoft surface models the touchscreen can stop working.
** Some models do not need this fix.
*You should install the latest updates from microsoft,including the driver packs before assuming there is a hardware problem.* - See Post #2
EDIT: If nothing else works try this fix - https://www.badcaps.net/forum/showpo...8&postcount=40
Always check a working dump from the same model using FIT.If the working dump default setting for "Integrated Sensor Hub Supported" is set to "NO"... -
i know a tool https://github.com/MuertoGB/MacEfiToolkit is capable of SN change and Clean ME but not updating EFI Version of the BIN file. is there a guide or a BIOS structure to update the firmware??...03-06-2024, 01:34 AM -
Hi,
I have an Anker SoundCore 2 (A3105) that I saved from the trash (well, I guess there's a reason why it was supposed to go into the trash...). The problem is that it always turns off after a few seconds (sometimes it stays on a bit longer, between 30 and 60 seconds, but it still turns off). The power light turns on and the bluetooth light starts blinking, but both abruptly turn off again. The "turn off sound" is still played after the lights turn off. Sometimes, it also loops the on-off cycle several times without me pressing any buttons. If I connect an AUX cable, music...08-11-2025, 02:14 PM -
Hello to everyone ,
This is my first post here, and i would like to share with you a small story in case you can help me.
Docker Type-C Gen 2 - Model 40AS. Was given to me by a friend for free ,but with the problem that you cannot use the video output ports.
All ports work , USB , Ethernet, Type C ... but HDMI + Display Port don't work
I searched on reddit and google for problem similar to that, and a LOT of people had fixed this problem by updating the firmware. So i tried , i searched and found 1.1.13 utility and 1.1.20 utility that can help... -
Hi guys.
I've got a Ubiquiti US-8-150W POE switch which has issues with updating the firmware.
Turned out to be a bad EEPROM chip. It would read the firmware and work as normal, but failed to write new firmware to it.
So I took off the chip and read on EEPROM and saved it. Wrote to old chip and failed to write
Got New chip and writes good.
THE PROBLEM...
It fails to fully load the firmware, POE lights fail to work during g firmware test during load. I'm suspecting bad EEPROM Read.
Does anyone have a Good Firmware I can have?...
Leave a comment: