volinakis
Badcaps Legend
Last Activity: Yesterday, 08:01 AM
Joined: 01-21-2021
Location: N/A
-
try... -
try...Leave a comment:
-
hardware1 file unlocked...Leave a comment:
-
thanks, I think for L14 gen2 is 384Kb (NPC68B) , mine took like 8 minutes to read 384Kb and all was "1F 1F"
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3652966}[/ATTACH]...Last edited by volinakis; 06-05-2025, 10:58 AM.Leave a comment:
-
How did you solve the problem reading NPC?...Leave a comment:
-
no, they are working. Error 20 appears when pins are not aligned or ribbon is faulty. I changed 32pins 0,5mm ribbon with 30pins 0,5mm from the svod kit because I had a lot of error 20 with 32pins ribbon after I used many times. You have to use a multimeter to check pins alignment microscope won't help. Check if you have last firmware and last software for SVOD4. Don't select any board, just select NUVOTON on Mode of programmer, 1,8V for Power and DISCONNECT trackpad, fingerprint, card reader, main battery, etc. Leave RTC batt. on. After plug in power adapter in motherboard check if power led is...
Leave a comment:
-
I asked for pic and 2nd bios chipset, it's FF because you read it wrong or erased before reading. If you want help do what I asked, having 2nd bios content I can figure out what's missing from empty chipset and rebuild it from update....Leave a comment:
-
I think bios is split into 2 chipsets, post a clear picture of region marked in yellow square. Read also 2nd chipset and post it here.
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3650283}[/ATTACH]...Leave a comment:
-
thank you....Leave a comment:
-
Please clean ME or provide MFIT 16.1.30.2264.
Thank you.
HP 840 G10
SN: 5CG4165891...Leave a comment:
-
extract Ec from update, is the .fl2 file or ask help from Maxpower3. I filled that area with 00 and it worked for me....Leave a comment:
-
fill with 00 [ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3641541}[/ATTACH]...
Leave a comment:
-
there is a facebook group for svod4, users are sharing their experiences there. Some are saying they let the main battery plugged in....Leave a comment:
-
it should work, few days ago I unlocked a T14 gen3 AMD. I think I have an older software version from March, I didn't update it to last version but I will try also with new version. Set voltage (power) to 1.8V, sometimes it helps even NPC isn't powered by SVOD4. I also let the CMOS battery plugged in so the motherboard doesn't start up. Oh, one last thing: I always remove motherboard from chassis or remove all connectors entering in motherboard....Last edited by volinakis; 05-19-2025, 12:06 PM.Leave a comment:
-
Thanks for sharing but it's not patch for your original bios. Is a patch for another bios from 660 G11 probably with clean ME. But good thing it's working for you, unfortunately we can't compare with original patched bios to figure out how to patch G11s.
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3639478}[/ATTACH]...Leave a comment:
-
thanks, I will try tomorrow....Leave a comment:
-
Hi, I need help with main bios and EC backups for HP ZBook 17 G6.
SN: 5CD015H8QH
After a failed update it doesn't boot anymore, just fans spinning endless. Cleaning ME it boots after I powered off 2-3 times and it appears message "HP Sure Start detected corruption in the Intel ME Select Continue to complete full recovery..." but it shuts down after 15-20 seconds and I can't power on from power button anymore, so I suspect also EC bios being corrupted - it suppose to recover ME from it. Analyzing EC bios dump with MEAnalyzer I have a lot of errors, including Error to File...Leave a comment:
-
👍...Leave a comment:
-
read posts, method is described by MaxPower3 in 1st post....Leave a comment:
-
it doesn't work, use SVOD4 to read NPC997...Leave a comment:
No activity results to display
Leave a comment: