-
Thanks bro. I wanna follow the method explained by SMDFlea mentioned in the thread. Can you share the ME analyzer version which can open this above image file and i can get the SKU information. -
Hello friends. I need firmvare pack for 11.8.93.4323, but I can't find it anywhere. Can someone help me?Leave a comment:
-
-
Hello I have a question
I replaced 10th gen intel cpu and cleaned me using fitc now board post fine but now not detecting ssd, what causes that and what setting do I need to do ?
This happened me on several intel me cleaning and I want to figure out why
Thanks in advanceLast edited by tomodachi; 04-22-2025, 07:21 AM.Leave a comment:
-
-
-
Hi,
Looking for clean stock firmware for ST: CG8PST3
Thank you.Leave a comment:
-
-
Hello!
Can you help me? I need clean ME Region RGN ver 16.0.1.1810
Thanks!Leave a comment:
-
-
-
Hi, I need clearme bios 5310, I have CSE ME 14.1.72.2287 Prod CorpLP CNPCMP-LP B A
but can't find the FIT version to clearme . I have attached the bios file that needs to be cleared.
Can someone provide me with the FIT version to open it?Leave a comment:
-
If you have to clean the ME firmware on **some microsoft surface models the touchscreen can stop working.
** Some models do not need this fix.
*You should install the latest updates from microsoft,including the driver packs before assuming there is a hardware problem.* - See Post #2
EDIT: If nothing else works try this fix - https://www.badcaps.net/forum/showpo...8&postcount=40
Always check a working dump from the same model using FIT.If the working dump default setting for "Integrated Sensor Hub Supported" is set to "NO"... -
i know a tool https://github.com/MuertoGB/MacEfiToolkit is capable of SN change and Clean ME but not updating EFI Version of the BIN file. is there a guide or a BIOS structure to update the firmware??...03-06-2024, 01:34 AM -
Hi,
I have an Anker SoundCore 2 (A3105) that I saved from the trash (well, I guess there's a reason why it was supposed to go into the trash...). The problem is that it always turns off after a few seconds (sometimes it stays on a bit longer, between 30 and 60 seconds, but it still turns off). The power light turns on and the bluetooth light starts blinking, but both abruptly turn off again. The "turn off sound" is still played after the lights turn off. Sometimes, it also loops the on-off cycle several times without me pressing any buttons. If I connect an AUX cable, music...08-11-2025, 02:14 PM -
Hello to everyone ,
This is my first post here, and i would like to share with you a small story in case you can help me.
Docker Type-C Gen 2 - Model 40AS. Was given to me by a friend for free ,but with the problem that you cannot use the video output ports.
All ports work , USB , Ethernet, Type C ... but HDMI + Display Port don't work
I searched on reddit and google for problem similar to that, and a LOT of people had fixed this problem by updating the firmware. So i tried , i searched and found 1.1.13 utility and 1.1.20 utility that can help... -
Hi guys.
I've got a Ubiquiti US-8-150W POE switch which has issues with updating the firmware.
Turned out to be a bad EEPROM chip. It would read the firmware and work as normal, but failed to write new firmware to it.
So I took off the chip and read on EEPROM and saved it. Wrote to old chip and failed to write
Got New chip and writes good.
THE PROBLEM...
It fails to fully load the firmware, POE lights fail to work during g firmware test during load. I'm suspecting bad EEPROM Read.
Does anyone have a Good Firmware I can have?...
Leave a comment: